The “Hot Tub AquaFill” is designed for use with above-ground portable spas, and like fountains, they require manual filling. The greatest drawback to filling your hot tub with a garden hose is the frequency of overflows and flooding associated with getting preoccupied with other tasks and forgetting to turn off the hose faucet. Water damage and homeowner policies can be a volatile issue in many said according to Don Griffin of the National Association of Independent Insurers, a trade association for property-casualty insurers. Chief among the cause of pool or hot tub overflows is forgetting to turn off the hose when filling or malfunctioning mechanical float control systems. These are nothing more than standard toilet tank floats (Fluidmaster) which often malfunction and will not shut off as they were designed to, resulting in an overflow and possible lawsuits from neighbors. The AquaFill has no troubleshooting list. It was designed to turn on and off one million times. The AquaFill float sensor is used in the canning and bottling industry and has a failure rate of only. The AquaFill’s sensor switch is designed to handle a continuous voltage of 120v. The pool Aquafill uses only 6 volts and the pond and fountain AquaFill only 24 volts. The Hot Tub AquaFill installs in approximately one hour and fits comfortably in any hot tub equipment space. Once installed, you will never have to fill your hot tub by hand again. The water level in the hot tub flows into the AquaFill assembly and into the float chamber where the water level equalizes. The assembly can be telescoped up and down for the purpose of adjusting the water level in the hot tub. The solenoid valve can be plumbed into either a return line or supply line for adding water to the hot tub as needed. The water supply to the solenoid can be as small as 3/8 the inch plastic or copper tubing, making it easy to hide in a variety of ways. The tubing can also be inserted in the joints of tile on a patio. The hot tub kit comes with the AquaFill assembly, 24-volt transformer, a solenoid valve (backflow preventer) and locks nut with rubber gasket seal. In the basic hot tub installation, drill a hole through the shell 5 to 6 inches below the desired water level. The threaded the male adapter through the hole and the rubber washer, and the rounded washer is tightened down to hold the assembly in place. Once installed, the assembly can then be telescoped up or down to establish the desired water level. In most cases, it will be necessary to have an electrician wire an 110 volt AC plug in the equipment compartment for the 24-volt transformer to plug into to supply the power for the Aquafill switch to operate the solenoid valve. The solenoid valve (w/backflow preventer) is plumbed into the supply or return lines. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “aquamediacorp” and is located in this country: US. This item can be shipped to North, South, or Latin America.
Balboa BP501 RetroFit Kit. Made in America. Option to Integrates with you iPhone, iTouch, Pad. The BP Series is the 1st in a newly designed and improved plat form that focuses on reliability. The BP501 uses a more advance carbon bases casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. This is a retrofit kit and is designed to replace a complete spa pack with any other manufactures hot tub heating system such as Gecko, Colman, Hydro Quip, Spa Guts, Arctic Spa, LA Spas, Beach Comber, Sundance, Emerald Spas, Maxx Spa, Hydro Spa, Hot Spring to name a few. The retrofit kit comes complete with the TP400 digital top side controller, and a set of cables for two pumps, and an ozone. Detailed retrofit instructions are also included so that a spa owner can quickly change over to BALBOA the world leader in Spa Heaters. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). And it now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). Although this spa pack. Can work at 120 VAC in which case it will produce 1.5 Kw of heat, it is primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s union tail pieces (included) fit standard 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day , various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 10.56″ High x 17″ Long x 4.8 Deep. Includes PN# 50260 TP400 Topside Controller with warm, cool, light, jets overlay. Includes: 2 sets of pump cables and an ozone cable with AMP connector for Balboa Spa Pack. Includes: Detailed instruction manual for installation to replace another brand of Spa Heater. 120 or 230 VAC ozone support (circ pump and ozone must have same voltage). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 4.0kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E14 or others made by Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Balboa TP400W with warm, cool, light, jets button (please not we can also substitute to the TP400T controller, please send us this request). Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store! The item “Balboa BP501 Retro Fit Kit- Spa Pack with TP400 Controller and cables” is in sale since Thursday, April 9, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.
Balboa BP501 RetroFit Kit – With WiFi Receiver. Made in America. Includes TP600 Top Side Controller & Wireless Adapter. Integrates with you iPhone, iTouch, Pad. The BP Series is the 1st in a newly designed and improved plat form that focuses on reliability. The BP501 uses a more advance carbon bases casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. This is a retrofit kit and is designed to replace a complete spa pack with any other manufactures hot tub heating system such as Gecko, Colman, Hydro Quip, Spa Guts, Arctic Spa, LA Spas, Beach Comber, Sundance, Emerald Spas, Maxx Spa, Hydro Spa, Hot Spring to name a few. The retrofit kit comes complete with the digital top side controller, WiFi adapter, and a set of cables for two pumps, and an ozone. Detailed retrofit instructions are also included so that a spa owner can quickly change over to BALBOA the world leader in Spa Heaters. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). And it now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). Although this spa pack can work at 120 VAC in which case it will produce 1.5 Kw of heat, it is primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s union tail pieces (included) fit standard 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day , various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 1 x 2-speed pump1, 1 x 1-speed pump2, Ozonator, 12v Light. 1 x 1-speed pump1, 1 x 1-speed pump2, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed pump1, 1 x 1-speed blower, Ozonator, 12v Light. 1 x 1-speed pump1, 1 x 1-speed blower, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed pump1, Ozonator, 12v Light. 1 x 1-speed pump1, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed 120v pump1, 120v Ozonator, 12v Light. 1 x 1-speed 120v pump1, 120v Circulation Pump, 120v Ozonator, 12v Light. 1 x 2-speed pump1, Circulation Pump, Ozonator, 12v Light. Setup 1-6 use 240v, pumps, blower and ozonator, although some field jumpers are available to mix 240 and 120 device. Connection for Audio/Visual components power (120 volt) is available as are connections to control auxiliary heater. 10.56″ High x 17″ Long x 4.8 Deep. Includes PN# 50056 TP600 Totpside Controller with warm, cool, light, jets overlay. Includes BWA 50350 Wi-Fi Module for use with iPhone, iPad, iPod, or Android device. Includes: 2 sets of pump cables and an ozone cable with AMP connector for Balboa Spa Pack. Includes: Detailed instruction manual for installation to replace another brand of Spa Heater. 120 or 230 VAC ozone support (circ pump and ozone must have same voltage). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 4.0kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E14 or others made by Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Balboa TP600 with warm, cool, light, jets1, jets2, flip button. Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store! The item “Balboa BP501 Retro Fit Kit- Spa Pack with TP600 Controller cables and Wi Fi” is in sale since Wednesday, April 6, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.
Balboa BP501 RetroFit Kit – With Receiver. Made in America. Includes TP400W Top Side Controller & Wireless Adapter. Integrates with you iPhone, iTouch, Pad. The BP Series is the 1st in a newly designed and improved plat form that focuses on reliability. The BP501 uses a more advance carbon bases casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. This is a retrofit kit and is designed to replace a complete spa pack with any other manufactures hot tub heating system such as Gecko, Colman, Hydro Quip, Spa Guts, Arctic Spa, LA Spas, Beach Comber, Sundance, Emerald Spas, Maxx Spa, Hydro Spa, Hot Spring to name a few. The retrofit kit comes complete with the digital top side controller, WiFi adapter, and a set of cables for two pumps, and an ozone. Detailed retrofit instructions are also included so that a spa owner can quickly change over to BALBOA the world leader in Spa Heaters. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). And it now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). Although this spa pack can work at 120 VAC in which case it will produce 1.5 Kw of heat, it is primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s union tail pieces (included) fit standard 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day , various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 10.56″ High x 17″ Long x 4.8 Deep. Includes PN# 50260 TP400 Totpside Controller with warm, cool, light, jets overlay. Includes BWA 50350 Wi-Fi Module for use with iPhone, iPad, iPod, or Android device. Includes: 2 sets of pump cables and an ozone cable with AMP connector for Balboa Spa Pack. Includes: Detailed instruction manual for installation to replace another brand of Spa Heater. 120 or 230 VAC ozone support (circ pump and ozone must have same voltage). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 4.0kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E14 or others made by Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Balboa TP400W with warm, cool, light, jets button (please not we can also substitute to he TP400T controller, please send us this request). Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store! The item “Balboa BP501 Retro Fit Kit- Spa Pack with TP400 Controller cables and Wi Fi” is in sale since Friday, February 19, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.
The Hot Tub AquaFill is designed for use with above-ground portable spas, and like fountains, they require manual filling. The greatest drawback to filling your hot tub with a garden hose is the frequency of overflows and flooding associated with getting preoccupied with other tasks and forgetting to turn off the hose faucet. Water damage and homeowner policies can be a volatile issue in many said according to Don Griffin of the National Association of Independent Insurers, a trade association for property-casualty insurers. Chief among the cause of pool or hot tub overflows is forgetting to turn off the hose when filling or malfunctioning mechanical float control systems. These are nothing more than standard toilet tank floats (Fluidmaster) which often malfunction and will not shut off as they were designed to, resulting in an overflow and possible lawsuits from neighbors. The AquaFill has no troubleshooting list. It was designed to turn on and off one million times. The AquaFill float sensor is used in the canning and bottling industry and has a failure rate of only. The AquaFills sensor switch is designed to handle a continuous voltage of 120v. The pool Aquafill uses only 6 volts and the pond and fountain AquaFill only 24 volts. The Hot Tub AquaFill installs in approximately one hour and fits comfortably in any hot tub equipment space. Once installed, you will never have to fill your hot tub by hand again. The water level in the hot tub flows into the AquaFill assembly and into the float chamber where the water level equalizes. The assembly can be telescoped up and down for the purpose of adjusting the water level in the hot tub. The solenoid valve can be plumbed into either a return line or supply line for adding water to the hot tub as needed. The water supply to the solenoid can be as small as 3/8 the inch plastic or copper tubing, making it easy to hide in a variety of ways. The tubing can also be inserted in the joints of tile on a patio. The hot tub kit comes with the AquaFill assembly, 24-volt transformer, a solenoid valve (backflow preventer) and locks nut with rubber gasket seal. In the basic hot tub installation, drill a hole through the shell 5 to 6 inches below the desired water level. The threaded the male adapter through the hole and the rubber washer, and the rounded washer is tightened down to hold the assembly in place. Once installed, the assembly can then be telescoped up or down to establish the desired water level. In most cases, it will be necessary to have an electrician wire an 110 volt AC plug in the equipment compartment for the 24-volt transformer to plug into to supply the power for the Aquafill switch to operate the solenoid valve. The solenoid valve (w/backflow preventer) is plumbed into the supply or return lines. The item “AquaFill Auto Fill Electronic Water Leveler for HotTubs- Complete Kit- Made USA” is in sale since Wednesday, September 30, 2015. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “aquamediacorp” and is located in Escondido, California. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.
Balboa BP501 RetroFit Kit. Made in America. Includes TP600 Top Side Controller. Optional – Integrates with you iPhone, iTouch, Pad. The BP Series is the 1st in a newly designed and improved plat form that focuses on reliability. The BP501 uses a more advance carbon bases casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. This is a retrofit kit and is designed to replace a complete spa pack with any other manufactures hot tub heating system such as Gecko, Colman, Hydro Quip, Spa Guts, Arctic Spa, LA Spas, Beach Comber, Sundance, Emerald Spas, Maxx Spa, Hydro Spa, Hot Spring to name a few. The retrofit kit comes complete with the TP600 digital top side controller, and a set of cables for two pumps, and an ozone. Detailed retrofit instructions are also included so that a spa owner can quickly change over to BALBOA the world leader in Spa Heaters. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). And it now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). Although this spa pack can work at 120 VAC in which case it will produce 1.5 Kw of heat, it is primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s union tail pieces (included) fit standard 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day , various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 1 x 2-speed pump1, 1 x 1-speed pump2, Ozonator, 12v Light. 1 x 1-speed pump1, 1 x 1-speed pump2, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed pump1, 1 x 1-speed blower, Ozonator, 12v Light. 1 x 1-speed pump1, 1 x 1-speed blower, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed pump1, Ozonator, 12v Light. 1 x 1-speed pump1, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed 120v pump1, 120v Ozonator, 12v Light. 1 x 1-speed 120v pump1, 120v Circulation Pump, 120v Ozonator, 12v Light. 1 x 2-speed pump1, Circulation Pump, Ozonator, 12v Light. Setup 1-6 use 240v, pumps, blower and ozonator, although some field jumpers are available to mix 240 and 120 device. Connection for Audio/Visual components power (120 volt) is available as are connections to control auxiliary heater. 10.56″ High x 17″ Long x 4.8 Deep. Includes PN# 50056 TP600 Totpside Controller with warm, cool, light, jets overlay. Includes: 2 sets of pump cables and an ozone cable with AMP connector for Balboa Spa Pack. Includes: Detailed instruction manual for installation to replace another brand of Spa Heater. 120 or 230 VAC ozone support (circ pump and ozone must have same voltage). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 4.0kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E14 or others made by Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Balboa TP600 with warm, cool, light, jets1, jets2, flip button. Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store! The item “Balboa BP501 Retro Fit Kit- Spa Pack with TP600 Controller and cables” is in sale since Friday, February 19, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.
Balboa EL2000 Retrofit Kit. Balboa EL2000 5.5-1.5 Kw Digital Spa Controller. Multiple Pumps- This is the world’s most advanced spa pack! – Made in America. This complete spa pack retrofit kit, is part of Balboa’s Elite line, it targeted at commercial spa owners or owners of residential spas who require some additional sophistication in the control options. The Balboa EL2000M3 has control options such as ozone suppression, clean up cycle after use, panel lock features, real time clock allowing filter cycles set by time of day and on a 12 hr or 24hr cycle, support of both 12 volt and 120 volt lights as well as fiber optic wheel lights and, importantly, this line supports wireless RF remote control. It uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). The standard retrofit kit comes with the sophisticated 8-button ML700 LCD top-side control panel (other panels are available). Although this spa pack can work at 120 VAC in which case it will produce 1.4KW of heat, it is primarily expected that it will be used at 230 VAC (requiring 30-60 AMP service) and will produce 5.5 KW of heat. One or more auxiliary heater, each producing 5.5kW can be slaved to the unit. It fits standard 2 piping making it ideal to upgrade any older mechanical or digital spa pack. Built in programmable features such a filter cycle programming by duration or time of day , various power saving modes including sleep mode, economy mode, standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. One 2-speed pump 1; one 1-speed pump 2 (which can be filed altered to handle a 2-speed pump); one blower or 3rd Pump 3; one circulation pump; one ozonator; one constant-on for Audio/Visual devices; one 12 volt light or LED or fibre wheel. The light circuit is convertible to 120 VAC. All receptacles can be switched to supply 120 Volts or 230 Volts. Retrofit Kit Comes complete with. EL2001M3 pak with 2 PVC heater tail pieces. ML700 8-button LCD digital control panel with 7′ cable. Two 4-wire 2-speed pump cables with 4-pin AMP plugs. Two 3-wire pump/blower cable with 4-pin AMP plug. One 12 volt light wiring assembly with 2-pin AMP plug. One loose 4-pin AMP plug with 4 pins (to adapt a non-Balboa ozonator). Plasticized control instruction sheet. Complete instruction manual for retrofit situations produced by Northern Lights. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). The M700 LCD digital topside control comes with 7 ft cable and includes Time, Mode/Prog, Warm, Cool, Light, Blower, Jets 1, Jets 2 buttons. Alternate lower cost ML400 4-button panel has Jets, Aux, Temp and Light buttons. 11.25″ High x 19.5″ Long x 4.60 Deep. Comes with 12 V light that will support LED lighting or fiber wheel lighting. RU and CSA, certification. Requires Balboa ML series panels and has connectors for 3 main panels and two auxiliary panels. Optional infrared remote control is available. Optional RF wireless control and monitoring is available (3 types of systems). 120 or 230 VAC ozone support. High or Low current mode. The flow through heater tube must be a minimum of 23 USGPM if the heater is 5.5kW. This flow rate should be checked if your spa uses a small circulation pump such as those made by Laing, Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. Can only handle pump 3 or blower, not both. MADE IN AMERICA not China! Pump supplying flow through heater must deliver 23 USGPM or more if heater is in 5.5kW mode. What is the difference between the VS520SZ and the EL2001M3 spa packs? See the Balbao Spec Sheet. The EL2001M3 has more control features and has wireless RF control and monitoring capability which the VS series spa packs do not have. The ML700 LCD digital topside control includes an overlay that has the functions as shown above and dimensions are as shown below. Balboa instruments top side controller. Balboa Spa Pack Features Comparison. 5.5 Kw Heater 220 VAC. Separate Optional Aux 5.5 Kw Heater. 240 VAC or 120 VAC. 120/240 Volt output receptacle. Separate voltage for ozone & blower. 2 -Speed Pump 1. 1-Speed Blower or Pump 3. Light switchable to 12 volt or 120 VAC. Fiber Optic Wheel Light. Standard, Economy, Sleep Mode. 12 hour filter cycle. 24 hour filter cycle. Filter cycle program by time of day. Clean up cycle (filter & ozone on after use). Only when jets are on. IR Dolphin Remote Control Option (short range). Optional Wireless Spa Monitor System. Tech Support 1 800 by NLCT. Note 1 – push button action with 1 speed pump 2 is OFF OFF ON. Note 2 – factory default is pump2 1-speed. Field changeable to support 2-speed pump2 but blower receptacle is then not active. Optional EL2001 Spa wireless controllers. Wireless Spa Remote Monitor. Your #1 Hot Tub Parts Replacement Store! The item “Balboa EL2000 Retrofit Kit- Spa Heater with cables, light, ML700 LCD controller” is in sale since Friday, February 19, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.
Balboa BP2000 RetroFit Kit. 5.5Kw Digital Spa Controller – With WiFi. Made in America. Includes TP800 Top Side Controller. Optional – Integrates with you iPhone, iTouch, Pad. And similar Android devices! The BP Series The BP Series is a newly designed and improved plat form that focuses on reliability. The BP2000 uses a more advance carbon bases casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. This is a high end retrofit kit suitable for tubs with multiple pumps (up to 5) and is designed to replace an older spa pack from from Balboa or other manufactures hot tub control system such as Gecko, Colman, Hydro Quip, Spa Guts, Arctic Spa, LA Spas, Beach Comber, Sundance, Emerald Spas, Maxx Spa, Hydro Spa, Hot Spring to name a few. The retrofit kit comes complete with the TP600 digital top side controller (TP800 is optional), and a set of cables and adapters (3x 4-wire for 2-spd pumps, 3 x 3-wire for 1-spd pumps and 1 x 2-wire light assembly). Detailed retrofit instructions are also included so that a spa owner with some electrical servicing knowledge can quickly change over to this equipment by BALBOA the world leader in Spa Heaters. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). And it now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). Although this spa pack can work at 120 VAC in which case it will produce 1.5 Kw of heat, it is primarily expected that it will be used at 230 VAC (requiring 40-60 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. Its union tail pieces (included) fit standard 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 1 or 2 filter cycle programming per day by duration or time of day , various power saving modes including oReady, oRest and oReady in Rest, High (80-104°F) and Low (50-99°F) temperature setting, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for supporting a wide range of configurations (setups) as illustrated in the table below. 11.50 High x 17 Long x 4.8 Deep. Includes : 3×4-wire 2-spd pump cables, 3 x 3-wire cables, 1x 12v light wire kit, 1 x BPX2 cable adapter kit, 1 x spare male AMP plug with pins. Includes: Detailed instruction manual for installation to replace another brand of Spa Heater. Ozone support (ozonator voltage will be same as voltage of heater pump). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 5.5 kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E14 or others made by Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. Can only handle maximum of 4 pumps or 3 pumps plus blower excluding the circulation pump if used. MADE IN AMERICA not China! PN# 50261 TP800 Topside Controller with Jets1, Jets2, Aux, Warm, Light, Cool control buttons (TP600 optional). Wireless Adapter PN 50350. Your #1 Hot Tub Parts Replacement Store! The item “Balboa BP2000 Retro Fit Kit- Spa Pack with TP800 Controller cables and WiFi” is in sale since Sunday, May 08, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.
