Spa / Hot Tub Pump – 1.5HP (2HP SPL) for spas and hot tubs requiring 1 speed motor 115 Volt. Or 230 Volt 2 Center Suction x Side Discharge Motor Description. Mfg: Century / A. Smith HP: 1.5 Service Factor 1.0 (2hp SPL) RPM: 3450 Single Speed 115 Volts – 16.3 Amps 230 Volts – 8.3 Amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description. Ultra Jet Mfg: Vico/Balboa P/N. The item “Hot Tub Pump 1.5 hp (2hp SPL) 2 Side Discharge Ultra Jet Vico 115/230V” is in sale since Wednesday, June 11, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Spa Hot Tub Pump 1.5HP SPL with Unions- For spas and hot tubs requiring 1 speed motors Direct replacement for Dreammaker Spa Motor Description: Mfg: Century HP: 1.5hp SPL RPM: 3450 Single Speed 115 Volts 13.6 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL15TDCS, 788379778361 1.5HP SPL 1 1/2″ Center Suction x Center Discharge 48 Frame 2 – 1.5″ Unions – 1 1/2 slip PVC. The item “Hot Tub Pump Vico Balboa Ultima, Ultra Jet, 1 1/2HP SPL, 1 Speed, 115Volts” is in sale since Sunday, May 04, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Spa Hot Tub Pump with Unions – 1.5HP for spas and hot tubs requiring 1 speed motors Direct replacement for Dreammaker Spa Motor Description: Mfg: Century HP: 1.5 SPL RPM: 3450 Single Speed 115 Volts 13.6 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL15SDCS, 5190-240, PKUL15HSDCS 1.5HP 1 1/2 Center Suction x Side Discharge 48 Frame. 2 – 1 1/2″ Unions – 1 1/2″ slip PVC. Optional Thermal Wrap Heater Information (shown above in second from last picture). This pump is built ready for the Hydro Thermix “Thermal Wrap” system. Snap It On – Free heat. Plumbing barbs (nipples) are built into the pump wet end for Thermal Wrap tubing connection points. Note: this listing does not include the Thermal Wrap Heat Jacket or tubing and clamps. This replacement pump and motor with Installed Thermal Wrap serves as the only heat source for many spa including: Quantum Xspa, Excaliber, Dreammaker, FreeFlo, PDC spas, SoftTub and others. The Thermal Wrap system can be retrofitted to work with most spas. The item “Hot Tub Pump Vico Balboa Ultima, Ultra Jet, 1.5 HP SPL, 1 Speed, 115V. WithUnions” is in sale since Sunday, February 23, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Dimension One Ozone Generator’89-’97 (Crystal Pure & Ultra Pure) – 01781-01. Replacement Ozone Generator for’89-’96 Crystal Pure Water Management Systems and’96-’97 Ultra Pure Water Management Systems. NOTE: If you are not sure which ozone you require for your spa, please message us with your spa’s serial number prior to ordering, and we will confirm for you. Our company name is Pool Spa Supplies, and our reputation is exemplary. Thank you for your business. Looking for hard to find pool and spa parts? Unsure of what you need? Give us a call, we can help! Why choose POOL SPA SUPPLIES? With 25 years in the pool and spa service industry, we know what it means to provide good customer service. Our technicians will even help you program your spa control. Tom can rattle off part numbers and replacements faster than you say POOL SPA SUPPLIES. We sure don’t get to talk about pools and spas when we go home after work, as that could bore our loved ones. The item “Dimension One Ozone Generator’89-’97 (Crystal Pure & Ultra Pure) 01781-01″ is in sale since Wednesday, July 01, 2015. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Other Pools & Spas”. The seller is “poolspasuppliesonline” and is located in Houston, Texas. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Indonesia.
Dimension One – Ozonator, Ozone Ultra Pure/Crystal Zone – 01781-16-A, 01781-16Y-A. Replacement Ozone Generator for 1998 – Current Ultra Pure and Crystal Zone Water Management. NOTE: If you are not sure which ozone you require for your spa, please message us with your spa’s serial number prior to ordering, and we will confirm for you. Our company name is Pool Spa Supplies, and our reputation is exemplary. Thank you for your business. Looking for hard to find pool and spa parts? Unsure of what you need? Give us a call, we can help! Why choose POOL SPA SUPPLIES? With 25 years in the pool and spa service industry, we know what it means to provide good customer service. Our technicians will even help you program your spa control. Tom can rattle off part numbers and replacements faster than you say POOL SPA SUPPLIES. We sure don’t get to talk about pools and spas when we go home after work, as that could bore our loved ones. The item “Dimension One Ozonator Ozone Ultra Pure/Crystal Zone 01781-16-A, 01781-16Y-A” is in sale since Tuesday, June 28, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Other Pools & Spas”. The seller is “poolspasuppliesonline” and is located in Houston, Texas. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, China, South Korea, Indonesia, Taiwan, South africa, Thailand, Hong Kong, Israel, New Zealand, Philippines, Singapore, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Malaysia.
Spa Hot Tub Pump 1HP with Pre-Installed “Thermal Wrap” Heater Jacket. For spas and hot tubs requiring 1 speed motors Motor Description: Motor Description: Mfg: Century HP: 1 RPM: 3450 Single Speed 115 Volts 11.8 – 12 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL10SDCS, 788379783402 1HP 1 1/2 Center Suction x Side Discharge. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet/Ultima Spa Pump With Thermal Wrap (Heat Transfer/Recycling System) For information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including: Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. The item “Hot Tub Pump 1hp Ultra Jet 1.5 with Thermal Wrap Heat Jacket BN25″ is in sale since Sunday, August 21, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Spa Hot Tub Pump 1.5HP (Full Rated) 2″ with Pre-Installed “Thermal Wrap Heater Jacket. Dual Voltage: 115/230 volts. For spas and hot tubs requiring 1 speed motors with 2 Center Suction/Side Discharge. Note: Typically this pump and motor is used on hot tubs requiring a 230 volt motor even though it’s dual voltage. For hot tubs requiring a 115 volt motor rated at 1.5HP, we recommend our single voltage motor. Motor Description: Mfg: Century HP: 1.5 – Service factor 1.0 (2hp SPL) RPM: 3450 Single Speed 115/230 Volts – dual voltage Amps: 16.5/8.3 HZ: 60 Frame: 56Z (48Y) Thermally Protected. Pump Description: Mfg: Vico/Balboa P/N. 1215123 (Identical to PKUL15SDCS2/2, 5190-250). 1.5 HP (2HP SPL) 2″ Center Suction x Side Discharge (1.5″ Connections available) 48 Frame. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet Spa Pump With Thermal Wrap (Heat Transfer/Recycling System). For more information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Can be used and retrofitted to work with most spas requiring 1.5 hp single speed, 3450 rpm, 115/230 volts pump motor. Note: Before ordering this “FULL RATED” 1.5 hp – as a replacement pump – make sure that your existing pump is not an “Uprated” pump. Sometimes manufactures call their pump a 1.5 HP when it’s really 1 hp. They call this an Uprated or SPL Pump. The motor amperage determines the true horse power. A 1 hp pump will be rated at approximately 11-14 amps. A 1.5 hp pump will be rated approximately 15 – 16 amps. Also note: you may think you have or need a pump for 2″ plumbing, when you actually need 1 1/2″. The pump connections measure larger than the actual pipe size used. The threaded connection on a 1 1/2″ pump measure 2 3/8″ – the threaded connections on a 2″ pump measure 3″. Unless otherwise specified, you will receive 2 pump connections with this listing. More about the – Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pump motors. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. Note: Thermal Wrap color may vary. Illustration showing water flow is of a 1.5″ pump – not 2″ per list listing. The item “Hot Tub Pump 1.5hp (Full Rated) Ultra Jet 2 with Thermal Wrap Jacket Heater” is in sale since Wednesday, March 05, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
X- Spadition & X-Calibur Hot Tub Pump 1HP (1.5 SPL) with Pre-Installed “Thermal Wrap” Heater Jacket. Original Pump with Heat Jacket used in both X-Spadition and X-Calibur hot tubs manufactured by Quantum Spas of Northwest Florida. The X-Spa and X-Calibur models were originally supplied with our Thermal Wrap Heat Jacket. Motor Description: Mfg: Century HP: 1 – Service factor 1.0 (1.5hp SPL) RPM: 3450 Single Speed 115 Volts, 13.6 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL10HSDCS 1 HP (1.5HP SPL) 1 1/2″ Center Suction x Side Discharge (2″ Connections available) 48 Frame. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet/Ultima Spa Pump With Thermal Wrap (Heat Transfer/Recycling System) For information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including: Quantum, Dreammaker, FreeFlo, PDC spas, SoftTub and others. This pump can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. The item “X-Spadition Hot Tub Pump, 1hp, 1.5 SPL, Ultra Jet 1.5 withThermal Wrap Heat Jacket” is in sale since Wednesday, February 10, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Spa Hot Tub Pump 1.5HP SPL – 2″ with Pre-Installed “Thermal Wrap Heater Jacket. For spas and hot tubs requiring 1 speed motors Motor Description: Mfg: Century HP:1.5hp SPL RPM: 3450 Single Speed 115 Volts 13.6 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL15SDCS2/2 5190-250 1.5 HP 2″ Center Suction x Side Discharge (1 1/2″ Connections available) 48 Frame. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet/Ultima Spa Pump With Thermal Wrap (Heat Transfer/Recycling System) For information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including: Quantum, Dreammaker, FreeFlo, PDC spas, SoftTub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. The item “Hot Tub Pump 1.5 hp SPL Ultima, Ultra Jet 2 with Thermal Wrap Heat Jacket” is in sale since Sunday, March 16, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Spa Hot Tub Pump 1.5HP Full Rated 1 1/2″ with Pre-Installed “Thermal Wrap Heater Jacket. Dual Voltage 115/230 volts. For spas and hot tubs requiring 1 speed motors. Note: Typically this pump and motor is used on hot tubs requiring a 230 volt motor even though it’s dual voltage. For hot tubs requiring a 115 volt motor rated at 1.5HP, we recommend our single voltage motor. Motor Description: Mfg: Century HP: 1.5 – Service factor 1.0 (2hp SPL) RPM: 3450 Single Speed 115/230 Volts – dual voltage Amps: 16.5/8.3 HZ: 60 Frame: 56Z (48Y) Thermally Protected. Pump Description: Mfg: Vico/Balboa P/N. PKUL15SDCS, 5190-240, PKUL15HSDCS 1.5 HP (2HP SPL) 1 1/2″ Center Suction x Side Discharge (2″ Connections available) 48 Frame. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet Spa Pump With Thermal Wrap (Heat Transfer/Recycling System). For more information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Can be used and retrofitted to work with most spas requiring 1.5 hp single speed, 3450 rpm, 115/230 volts pump motor. Note: Before ordering this “FULL RATED” 1.5 hp – as a replacement pump – make sure that your existing pump is not an “Uprated” pump. Sometimes manufactures call their pump a 1.5 HP when it’s really 1 hp. They call this an Uprated or SPL Pump. The motor amperage determines the true horse power. A 1 hp pump will be rated at approximately 11-14 amps. A 1.5 hp pump will be rated approximately 15 – 16 amps. Also note: you may think you have or need a pump for 2″ plumbing, when you actually need 1 1/2″. The pump connections measure larger than the actual pipe size used. The threaded connection on a 1 1/2″ pump measure 2 3/8″ – the threaded connections on a 2″ pump measure 3″. Unless otherwise specified, you will receive 1 1/2 pump connections. More about the – Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pump motors. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. Note: Thermal Wrap color may vary. The item “Hot Tub Pump 1.5hp (Full Rated) 1 1/2 Ultra Jet with Thermal Wrap Heat Jacket” is in sale since Thursday, February 27, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
