In good working condition. Item does exhibit some light wear from prior use that has not affected the overall functionality. Please view listing photos for further condition details. This listing includes all items pictured in listing photos ONLY. If it is not pictured, please assume it is NOT included. Type : Swimming Pool Pump. Material : Stainless Steel, Copper, Steel, Plastic. Item Height : 11.4 in. Suitable For : Hot Tubs, Above Ground Pools, In Ground Pools. Tank Lining Material : Copper. Minimum Pump Power Requirement : 2 hp. Features : Antibacterial, Rust Resistant, Easy Installation, Chlorine Resistant. At Everyday Fulfillment KC, we take pride in our great customer service. Please allow time for communication after hours and during weekends & holidays. We reserve the right to cancel any order for any reason. We are not responsible for undeliverable addresses. We DO NOT guarantee, offer or have any control over warranties of any kind.
More info at : Spa Pumps And More. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-1000 top side keypad/display, it is 2.5″ x 5.5″ and drops into a 1.7″ x 4.7″ cutout. You will receive the 2.5″ x 5.5″ if you order from this listing. For more information look at Spa Pumps And More. Their part number is SMTD1500. Alternate part number is ePack. Model: ePack SMTD 1500. Display: Digital Topside Keypad 2.5×5.5. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. There is a larger top side available at slightly higher cost, it is the KP-2010 and is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. If you are interested in this, see our other listing for the ePack with KP-2010 top side. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. More details at Spa Pumps And More.
More info at Spa Pumps And More. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. For more information look at Spa Pumps And More. Their part number is SMTD1500. Alternate part number is ePack. Model: ePack SMTD 1500. Display: Digital Topside Keypad 3.25″ x 7.25″. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. Comes with KP-2010 top side keypad/display, it is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. You will receive the 3.25″ x 7.25″ if you order from this listing. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. This model is NOT for tiny 3/4 circ pumps. For low flow controls and pumps go to Spa Pumps And More and give them all your details. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Look at Spa Pumps And More for further details.
Acc Smart touch Digital 2000 spa control for retrofitting your old existing spa control. The 2000 can control can operate a 2 speed primary pump, a 2 speed secondary pump, a single speed air blower, a 12 volt spa light, an auxiliary light or accessory and an ozonator. The system comes with a calibrated pressure switch, a heavy duty 2 pole contactor to control the 5.5 KW attached heating element. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “a-1spacontrol” and is located in this country: US. This item can be shipped to United States.
Because the factory will be shut down 12/24-1/2 and because these are built to order, please allow 5-10 days to build. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Model: ePack SMTD 1500. Display: Digital Topside Keypad 3.25 x 7.25. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. Comes with KP-2010 top side keypad/display, it is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. You will receive the 3.25″ x 7.25″ if you order from this listing. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL PACK HOT TUB HEATER CONTROLLER ePack ACC KP-2010 4kW 115/230v” is in sale since Wednesday, November 3, 2021. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “distributorsfulfillment” and is located in Los Angeles, California. This item can be shipped to United States.
Southern California, the pandemic has caused numerous material & labor shortages. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-1000 top side keypad/display, it is 2.5″ x 5.5″ and drops into a 1.7″ x 4.7″ cutout. You will receive the 2.5″ x 5.5″ if you order from this listing. Model: ePack SMTD 1500. Display: Digital Topside Keypad 2.5×5.5. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. There is a larger top side available at slightly higher cost, it is the KP-2010 and is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. If you are interested in this, see our other listing for the ePack with KP-2010 top side. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL PACK HOT TUB HEATER CONTROLLER ePack ACC 4kW 115/230v built to order” is in sale since Wednesday, October 13, 2021. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “distributorsfulfillment” and is located in Los Angeles, California. This item can be shipped to United States.
Southern California, the pandemic has caused numerous material & labor shortages. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-1000 top side keypad/display, it is 2.5″ x 5.5″ and drops into a 1.7″ x 4.7″ cutout. You will receive the 2.5″ x 5.5″ if you order from this listing. Model: ePack SMTD 1500. Display: Digital Topside Keypad 2.5×5.5. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. There is a larger top side available at slightly higher cost, it is the KP-2010 and is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. If you are interested in this, see our other listing for the ePack with KP-2010 top side. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL PACK HOT TUB HEATER CONTROLLER ePack ACC 4kW 115/230v built to order” is in sale since Thursday, June 3, 2021. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “distributorsfulfillment” and is located in Los Angeles, California. This item can be shipped to United States.
Due to extremely high demand and ACC Holiday schedule this control has up to a 1-2 week leadtime to be built, tested. And packed before it ships out. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-1000 top side keypad/display, it is 2.5″ x 5.5″ and drops into a 1.7″ x 4.7″ cutout. You will receive the 2.5″ x 5.5″ if you order from this listing. Model: ePack SMTD 1500. Display: Digital Topside Keypad 2.5×5.5. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. There is a larger top side available at slightly higher cost, it is the KP-2010 and is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. If you are interested in this, see our other listing for the ePack with KP-2010 top side. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL PACK HOT TUB HEATER CONTROLLER ePack ACC 4kW 115/230v built to order” is in sale since Sunday, December 6, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “distributorsfulfillment” and is located in Los Angeles, California. This item can be shipped to United States.
Due to extremely high demand this control has a 1-2 week leadtime to be built, tested. And packed before it ships out. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-1000 top side keypad/display, it is 2.5″ x 5.5″ and drops into a 1.7″ x 4.7″ cutout. You will receive the 2.5″ x 5.5″ if you order from this listing. Model: ePack SMTD 1500. Display: Digital Topside Keypad 2.5×5.5. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. There is a larger top side available at slightly higher cost, it is the KP-2010 and is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. If you are interested in this, see our other listing for the ePack with KP-2010 top side. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL PACK HOT TUB HEATER CONTROLLER ePack ACC 4kW 115/230v built to order” is in sale since Sunday, October 4, 2020. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “distributorsfulfillment” and is located in Los Angeles, California. This item can be shipped to United States.
