More info at : Spa Pumps And More. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-1000 top side keypad/display, it is 2.5″ x 5.5″ and drops into a 1.7″ x 4.7″ cutout. You will receive the 2.5″ x 5.5″ if you order from this listing. For more information look at Spa Pumps And More. Their part number is SMTD1500. Alternate part number is ePack. Model: ePack SMTD 1500. Display: Digital Topside Keypad 2.5×5.5. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. There is a larger top side available at slightly higher cost, it is the KP-2010 and is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. If you are interested in this, see our other listing for the ePack with KP-2010 top side. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. More details at Spa Pumps And More.
Due to extremely high demand this control has a 4 to 7 day leadtime to be built, tested. NEW hot tub controller, with electric high flow heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for pump, air blower, light, and ozonator, for standard 60hz 4-wire 230 volt with a neutral incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2″ pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 12″Tx15″Wx5D approximately. Includes the 3.25×7.25″ large BACKLIT topside, which requires cutout hole of 2.2×6.2″ hole. The ribbon cable from topside to control box is 5ft long. Note: Control box is now black in color, not blue. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump. And an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the high flow heater included. Cord to main 2-speed pump is 48, the cords to light, ozonator, and air blower are short pigtails meant to splice onto your existing cords using wire nuts. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps, if you need a low flow circ pump system, please message us. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “angelessupply” and is located in this country: US. This item can be shipped to United States.
NEW hot tub controller, with electric high flow heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2″ pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. Includes the 3.25×7.25″ large topside, which requires cutout hole of 2.2×6.2″ hole. The ribbon cable from topside to control box is 5ft long. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump. And an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the high flow heater included. Cord to main 2-speed pump is 48, the cords to light, ozonator, and air blower are short pigtails meant to splice onto your existing cords using wire nuts. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps, if you need a low flow circ pump system, please message us. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. The item “Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500″ is in sale since Friday, January 11, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “warehousethirtythree” and is located in Southern, California. This item can be shipped to United States.
New hot tub controller, with electric high-flow heater, by applied computer controls, acc model ‘epack’ smtd1500, complete, with set of power cords (pigtails) for pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel heater, 2″ pipe size couplings, standard threaded split nuts 4.0kw heater. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″tx14″wx4.5d approximately. Made in the usa. Great tech support, message us anytime for help, questions, troubleshooting, whatever you need. Standard 2.5×5.5″ topside, the 2.5×5.5 requires cutout hole of 1.7×4.7″ to drop into. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The epack will run one main 2-speed pump. And an air blower on-off, or, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. If you need to control more than this, look at the model 2000, the smtd2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. For 4-wire 230v incoming power or for 115v incoming power. Not for 3-wire 230v please note! Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Acc epack smtd1500 control with 4kw high-flow heater. Set of pigtail power cords for pump, light, ozonator and air blower. High-flow 15″ 4kw heater for 2″ or 1-1/2 plumbing size, minimum flow required is 20 gpm. Top side display//keypad 2.5 x 5.5″ with 57″ cable.The item “Spa Control Hot Tub Heater Controller Pack ACC ePack SMTD1500 115/230v NEW 4kw” is in sale since Thursday, January 01, 2015. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “the_warehouse” and is located in California. This item can be shipped to United States.
