Balboa® – BP7 5.5 KW Control Bundle W/ SpaTouch Square Topside – 50-BP7-SS-55-K. The BP is the most reliable and. Widely used system in the industry. Supports all TP and SpaTouchT topsides (LED, Color LCD and Touchscreens). Supports all BP ancillary products (ControlMySpaT, BBAT, CZT and Status Pro). Balboa BP7 Control System Only FEATURES. 7 relays allow BP7 to operate in 32 different setups, which can power a spa with 1-4 pumps. BP7 can replace any Balboa BP System while using the existing topside that is already installed on the spa (some exceptions may apply). BP7 can replace any Balboa VS or EL System when you match it with any TP or SpaTouch topside panel (some exceptions may apply). BP7 can replace any Balboa or other brand’s non-low flow system when you match it with amy TP or SpaTouch topside panel (some exceptions may apply). Supports – ControlMySpa, Balboa Bluetooth Audio, Chromozon3, and Status Pro. Dimensions: 17″L x 4.75″W x 11.5H.

Softub Hot Tub Pump Replacement. Typically used in “European” markets. 1 HP, 230 Volts, 50HZ, Single Speed with Pre-Installed “Thermal Wrap” Heater Jacket. Motor & Pump with Pre-installed Thermal Wrap. Motor: Manufacture : US Motors (AGH10FL1) Horse Power: 1 Service Factor 1.0 (Often labeled 1.5hp SPL) Volts: 220-240 Amps: 6.0/6.3 RPM: 2850/3450 Frame: 48Y – Thru Bolt W/Base. Pump: (pre-installed on motor) Mfg: Balboa/Vico. 1 HP (1.5HP SPL) 1 1/2 Center Suction x Center Discharge – pump threads fit your existing pump disconnects/split unions. 1 Thermal Wrap Heat Jacket: Pre-installed on motor. (top port on Thermal Wrap is plugged and not used for Softub applications). 32″ 3/8″ ID Tubing (for making tubing connections between the 2 ports on Thermal Wrap to your existing coil/hose ports in your plumbing). More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap. Collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths. Captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). Note: If the pump/connections pictured above do not exactly match the pump have? Give me a call to discuss your application, we either have the pump you need or have other available options that will work for your application. Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including. Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. Even if you have an electric heater on your spa, the Thermal Wrap System will compliment your electric heater by capturing the waste heat. The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action.

Balboa® – BP7 4.0 KW Control Box Bundle With SpaTouch Square Topside – 50-BP7-SS-40-K. The BP is the most reliable and. Widely used system in the industry. Supports all TP and SpaTouchT topsides (LED, Color LCD and Touchscreens). Supports all BP ancillary products (ControlMySpaT, BBAT, CZT and Status Pro). Balboa BP7 Control System Only FEATURES. 7 relays allow BP7 to operate in 32 different setups, which can power a spa with 1-4 pumps. BP7 can replace any Balboa BP System while using the existing topside that is already installed on the spa (some exceptions may apply). BP7 can replace any Balboa VS or EL System when you match it with any TP or SpaTouch topside panel (some exceptions may apply). BP7 can replace any Balboa or other brand’s non-low flow system when you match it with amy TP or SpaTouch topside panel (some exceptions may apply). Supports – ControlMySpa, Balboa Bluetooth Audio, Chromozon3, and Status Pro. Dimensions: 17″L x 4.75″W x 11.5H.

This item is new out of box. Please see photos for details. It is guaranteed to be in good working order. The sale includes only what is shown. We are dedicated to providing excellent customer service. If the value of the order is over two hundred dollars then we require a signature confirmation. A delay in contacting us may result in our not being able to meet your requirements. We will then give you instructions on how to proceed. Powered by SixBit’s eCommerce Solution.

Balboa Water Group 54217-Z 50-54217-Z, one-Size. Includes topside control panel. Controls one dual-speed pump, blower or second one-speed pump, ozone and light. 18 x 16 x 14 inches. 4.0 out of 5 stars. #226,375 in Patio, Lawn & Garden. #4,853 in Pool & Spa Replacement Parts.

Condition is used working, taken out of leaking tub. Serial number noted on photos. Should be installed by professional. Will come exactly as pictured. Nothing else is included in this listing.

Balboa – Topside Panel, Balboa 54112, VL701S – 54112 (With Overlay 10430).

1 HP 2-Speed Spa Pump 120 Volts – Balboa Ultima / Victoria. Frame 48, 10.3/3.8 Amp motor, 1-1/2 side discharge wet end. Formerly marked as Ultima model by UltraJet, Vicco, Pentair and Balboa. Can Also be used as 1-Speed 1 HP Pump. 1 HP Ultima Victoria Pump (1.5 HPR). Balboa’s Victoria pumps provide long life, excellent performance, value pricing and. Configuration flexibility all in a cost-effective package. Flow rates for this pump can be up 100 gallons per minute (see below 1HP pump curves). Features. All seals are carbon ceramic with Viton® elastomers for long-lasting performance, easily enduring prolonged heat and chemical exposure. Multi-direction volute mounting and options deliver the greatest range of plumbing configurations. Frame 48 motor design. Two-speed motor. 115 volt. UL and CSA certified. This pump is intended as a replacement for common 1 HP 120 volt side discharge pumps that use 1-1/2 unions. The motor is a two speed pump but can also replace any single 1 speed 1HP pump (120 VAC). The pump is typically wired directly to the pump receptacles of a spa pack. Safety features include auto overheat shut off protection. Comes complete with two x 1 1/2 replacement unions. Drain plug ensures no water is left in the pump body during storage, which is useful for hygienic reasons and also prevents freeze damage where applicable. All Victoria (formerly Ultima) pumps have discharge and suction nipples that allow for a side stream flow, for such purposes as an ozonator venturi. If your hot tub uses these nipples, they must first be drilled out on the new replacement pump before they become active. Balboa is the largest spa parts manufacture in the world. These pumps are NOT CHINESE and are proudly manufactured in the USA (Tustin, California). Comes with 1 1/2 pump unions. Amps = 10.3/3.8 amps. Rpm = 3450/1725 rpm. 110, 115, 120 VAC 60 Hz, 2 speed (optional 1 speed if you connect only to the high speed terminal). Frame = 48 (5.85 wide motor). Length = 15.32. Height = 7.58. Connection side = 1 1/2. Flow Curve & Dimensions. Download Ultima Spa Pump Technical Specifications. Your #1 Hot Tub Parts Replacement store!

Balboa BP501 Spa Pack – Hot Tub Heater-56485-05 With Wireless Controller. Comes with a good used spa controller that need a the cord spliced back together.

Made in America. Integrates with you iPhone, iTouch, Pad, or Android! The BP Series is the 1st in a newly designed and improved platform that focuses on reliability. The BP501 uses the same Zircaloy or Titanium heater elements as used in the VL and EL series spa pack. The new BP501 utilizes a more advance carbon based casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). The BP Series now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). This spa pack can work at 120 VAC in which case it will produce 1.4 Kw of heat. It is however primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s standard spa pack union tail pieces fit 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day, various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 10.56″ High x 17″ Long x 4.8 Deep. Requires Balboa TP series panels and has connectors for 1 main panels and 1 auxiliary panels. Optional Wi-Fi Module for use with iPhone, iPad, iPod, or Android device. 120 or 230 VAC ozone support (ozone must have same voltage as heater pump). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 5.5kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E10 or others made by Grundfos or Waterway. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Works with the following Balboa Top Side Controllers. Balboa TP600, Balboa TP400, TP600, TP900. Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store!