»
S
I
D
E
B
A
R
«
Spa Control Hot Tub Heater & Controller SMTD1000 2.5×5.5 Topside ACC 5.5kW NEW
Mar 11th, 2019 by admin
Spa Control Hot Tub Heater & Controller SMTD1000 2.5x5.5 Topside ACC 5.5kW NEW


Spa Control Hot Tub Heater & Controller SMTD1000 2.5x5.5 Topside ACC 5.5kW NEW


Spa Control Hot Tub Heater & Controller SMTD1000 2.5x5.5 Topside ACC 5.5kW NEW


This Smartouch Digital Control comes with 15 heater, power cords, and is a complete unit to replace your old spa control and heater. Runs a main 2 speed spa pump, and an air blower or 2nd pump, and spa light, and has an output for ozonator or ionizer or any other non-switched device. Intended use is to be mounted under the redwood skirt of a typical portable spa, not outside in the rain, snow, etc. Runs on 20 GPM minimum , 2″ or 1-1/2″ PVC pipe size. This is not a circ pump system for tiny 24/7 3/4 pumps. This is for conventional 2-speed pump and is a high flow heater and control system. Message us if you need a tiny circ pump controller. Comes with a new power cord for your main 2-speed pump, with quick disconnect plug to the control. You also get quick disconnect plugs and short’pigtail’ cords for the air blower, spa light, and one accessory device, like an ozonator. These are short cords meant to splice to your existing light cord, blower cord, and ozonator cord, using the supplied wire nuts. Includes 15 inch long 5500 watt (5.5kw) stainless steel heater, can be used on 115v or 230 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The Smartouch SMTD 1000 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115v or 230v. On a 115 volt source, the heater will be 1.4kw or 1375 watts. From the factory the SMTD1000 is set for 230v incoming power, 230v to the heater, and 115v to the pump, air blower (or second pump), and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by ACC, and ready to go as is. Control box stands 14.6″ tall, and 15.4″ wide, 7″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By ACC, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by Applied Computer Controls. ACC has been building digital hot tub controls over 30 years. Message us anytime for tech support, questions, or just general help, or we’re happy to call you if you want to chat. Smartouch Digital Control by ACC model SMTD1000 for 4-wire 230v or 3-wire 115v. (not for 3-wire 230v). 15 stainless steel heater with standard threaded couplings. Digital display keypad (topside) 2.5×5.5″ with 57″ long cable. Extension cords available at extra cost, message us please. Pump 4 wire power cord 48 long with quick disconnect AMP plug and motor connectors. Air Blower power cord 3 foot with quick disconnect AMP plug, 18/3 wire size, to splice to existing blower cord. Ozonator pigtail with quick disconnect AMP plug, 18 gauge wire. Light pigtail with quick disconnect AMP plug, 18 ga wire. ACC User’s Manual. The item “Spa Control Hot Tub Heater & Controller SMTD1000 2.5×5.5 Topside ACC 5.5kW NEW” is in sale since Tuesday, January 1, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “warehousethirtythree” and is located in Southern, California. This item can be shipped to United States.

  • Country/Region of Manufacture: United States
  • Type: high flow
  • MPN: SMTD1000
  • Brand: ACC
Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords
Mar 2nd, 2019 by admin
Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords


Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords



A very nice replacement control works on most any hot tub or portable spa, replacing your old control and heater. Includes stainless steel 2 inch diameter high flow 5kw heater, 15 long, standard size. Ships from Spa Pumps And More. A very complete kit with topside and 6 cords for pump, blower, topside, temp sensor, secondary pump, and light. This makes the unit fully self-contained, so you won’t have to locate the temp sensor yourself, saves time! Message us though, please. This CBT7 Control comes with 5kw 15″ high flow heater, 2.5×5.0″ Topside display/keypad, pump and blower and light and secondary pump cords, and is a complete unit to replace your old spa control and heater. Topside drops into a 1-3/4 round cutout in your spa. Intended for use under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. Runs a main 2 speed spa pump, and an air blower or other device, a secondary pump, and spa light, and has a receptacle for ozonator or ionizer or any other non-switched device. Comes with new power cords for your main 2-speed pump and an air blower, light, and secondary pump, with quick disconnect plugs to the control. Temperature sensor comes with a long cord so you can either mount the sensor onto the heater, or, mount it in your tub if your tub has a drywell, has provision for a remote temp sensor. Cord is 8 feet long, but again it is your choice to mount it right on the heater or stick the sensor into a tub fitting you already have. Includes 15 inch long stainless steel high flow 2 heater, with 5kw Incoloy element. Can be used on 115/120v or 230/240 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The CBT7 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115/120v or 230/240v. On a 115/120 volt source, the heater will be 1.25kw or 1250 watts. From the factory the CBT7 is set for 230/240v incoming power, 230/240v to the heater, and 230/240v to the pumps. 115/120v to the air blower, and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by United, and ready to go as is. Control box stands 11.1″ tall, and 15.5″ wide, 3.4″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By United Spas, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by United Spas. United has been building digital hot tub controls over 20 years. CBT7 Digital Control by United Spas model C5. 15″ stainless steel high flow 5kW heater with standard threaded couplings for 2″ PVC plumbing. Digital display keypad (topside) 2.5×5.0 with 9.5 foot long cord. Drops into 1-3/4 round cutout. One pump power cord 4-wire for a 2-speed pump, 45 long with quick disconnect AMP plug and motor connectors. Air Blower power cord 57 with quick disconnect AMP plug, 18/3 wire size. Light cord with quick disconnect AMP plug, 8 foot long. Temperature sensor and cord. A secondary pump cord. United Spas t& Topside Installation Manual & User’s Guide. United Spas C5 Series Installation & Service Manual. Additional info: Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. The item “Hot Tub Heater Control Digital Spa Controller Pack C5 United Spas CBT7 & 6 cords” is in sale since Thursday, February 7, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “tazi_discounts” and is located in Los Angeles, California. This item can be shipped to United States.

  • Modified Item: No
  • Country/Region of Manufacture: United States
  • Custom Bundle: No
  • MPN: Does Not Apply
  • Brand: United Spas
  • Non-Domestic Product: No
  • Distributed by:: Spa Pumps And More
Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500
Feb 12th, 2019 by admin
Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500


Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500


Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500


Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500


NEW hot tub controller, with electric high flow heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2″ pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. Includes the 3.25×7.25″ large topside, which requires cutout hole of 2.2×6.2″ hole. The ribbon cable from topside to control box is 5ft long. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump. And an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the high flow heater included. Cord to main 2-speed pump is 48, the cords to light, ozonator, and air blower are short pigtails meant to splice onto your existing cords using wire nuts. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps, if you need a low flow circ pump system, please message us. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. The item “Spa Control Hot Tub Heater ePack Controller Big Keypad 115/230v ACC 4kw SMTD1500″ is in sale since Friday, January 11, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “warehousethirtythree” and is located in Southern, California. This item can be shipped to United States.

  • material: plastic enclosure, stainless high flow heater
  • Model: SMTD1500
  • Country/Region of Manufacture: United States
  • Capacity: High Flow Heater 20 GPM minimum on 1-1/2″ or 2″ pv
  • MPN: SMTD1500
  • Brand: ACC
Spa Control Hot Tub Heater Controller Pack ACC SMTD1000 Large Keypad Special
Feb 3rd, 2019 by admin
Spa Control Hot Tub Heater Controller Pack ACC SMTD1000 Large Keypad Special


Spa Control Hot Tub Heater Controller Pack ACC SMTD1000 Large Keypad Special


Spa Control Hot Tub Heater Controller Pack ACC SMTD1000 Large Keypad Special


Spa Control Hot Tub Heater Controller Pack ACC SMTD1000 Large Keypad Special


Spa Control Hot Tub Heater Controller Pack SMTD1000 Big Topside NEW 115/230v ACC – this one is new, complete, an open box manager’s special 1 only at this special price. This Smartouch Digital Control comes with 15″ high flow 2″ heater, Large 3.25×7.25 Topside display/keypad, power cords, and is a complete unit to replace your old spa control and heater. Drops into 2.5×6.5 cutout in your spa. Runs a main 2 speed spa pump, and an air blower, and spa light, and has an output for ozonator or ionizer or any other non-switched device. Intended use is to be mounted under the redwood skirt of a typical portable spa, not outside in the rain, snow, etc. Runs on 20 GPM minimum , 2″ or 1-1/2″ PVC pipe size. This is NOT a circ pump system for tiny 24/7 3/4 pumps. This is for conventional 2-speed pump and is a high flow heater and control system. Message us if you need a tiny circ pump controller, along with all your specs and details. This control above is NOT for low flow circ systems. Comes with a new power cord for your main 2-speed pump, with quick disconnect plug to the control. You also get quick disconnect plugs and short’pigtail’ cords for the air blower, spa light, and one accessory device, like an ozonator. These are short cords meant to splice to your existing light cord, blower cord, and ozonator cord, using the supplied wire nuts. Includes 15 inch long 5500 watt (5.5kw) stainless steel heater, can be used on 115v or 230 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The Smartouch SMTD 1000 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115v or 230v. On a 115 volt source, the heater will be 1.4kw or 1375 watts. From the factory the SMTD1000 is set for 230v incoming power, 230v to the heater, and 115v to the pump, air blower (or second pump), and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. Control is intended for use under the redwood skirt of a portable spa, not outside in the rain please note. This control is for 4-wire 230v or for 115v. IF you need a control for 3-wire 230v, an all 230v system, we can supply it, takes an extra day or so, message us and we’ll respond with price and leadtime. So message us if you want 3-wire, please. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by ACC, and ready to go as is. Control box stands 14-9/16″ tall, and 15-3/8″ wide, 7″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By ACC, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by Applied Computer Controls. ACC has been building digital hot tub controls over 30 years. Message us anytime for tech support, questions, or just general help, or we’re happy to call you if you want to chat. Smartouch Digital Control by ACC model SMTD1000. 15 stainless steel heater with standard threaded couplings. Large digital display keypad (topside) 3.25×7.25″ with 57″ long cable. Pump 4 wire power cord with quick disconnect AMP plug and motor connectors. Air Blower power cord, a short’pigtail’ with quick disconnect AMP plug, 18/3 wire size, to splice to existing blower cord. Ozonator cord, a short pigtail with quick disconnect AMP plug, 18 gauge wire. Light pigtail with quick disconnect AMP plug, 18 ga wire. ACC User’s Manual. Manual and Programming Guide can be viewed and printed on the ACC-Spas website. Be sure to add me to your favorites list. Check out my other items. The item “Spa Control Hot Tub Heater Controller Pack ACC SMTD1000 Large Keypad Special” is in sale since Friday, January 11, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “warehousethirtythree” and is located in Southern, California. This item can be shipped to United States.

  • Country/Region of Manufacture: United States
  • Type: high flow
  • MPN: SMTD1000
  • Brand: ACC

Recent searches

  • SMTD1000 miami fl
Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump
Feb 1st, 2019 by admin
Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump


Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump


Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump


Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump


Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump


1 only at this special price! NEW hot tub controller, with electric heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, witn NEW 2-speed pump, 3.1 threaded connection with pair of pump unions, pump is 115 volt Motor, rated 8.8 amps 115 volts. Control comes with a set of plugs including a power cord for pump, and pigtails for air blower, light, and ozonator, and can run on 230 volt or 115 volt, it is convertible for voltages. 15″ stainless steel heater, 2″ pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. 2-speed pump is 115v, 8.8 amps. Main control box is 11.5″Tx14″Wx4.5″D Includes the 2.5×5.5″ small topside, which requires cutout hole of 1.7 x 4.7 hole. The ribbon cable from topside to control box is 5ft long. We do not abandon our customers after the sale! We HAVE the field experience and staff to support you, our field service staff is ready to talk to you, answer questions, lend support, anytime! For repairing your portable spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! Factory default settings are setup for 230 volt power incoming, 230v to heater, 115v out to main 2 speed pump, 115v to air blower or 2nd pump, 12v out to light, 115v out to ozonator or other accessory. Like all spa controls, this is intended to be used on portable spas, mounted under the redwood skirt, not designed to sit out in the rain please note. Ships fast, in stock now. Pump, 2 speed 115v and a pair of pump union fittings. Check out my other items. Be sure to add me to your favorites list. The item “Spa Control Hot Tub Heater 230/115v 4kW ePack Controller Pack & 2 speed Spa Pump” is in sale since Tuesday, January 1, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “warehousethirtythree” and is located in Southern, California. This item can be shipped to United States.

  • Country/Region of Manufacture: United States
  • MPN: Does Not Apply
  • Brand: ACC
Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new
Jan 24th, 2019 by admin
Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new


NEW spa control system, complete, by United Spas, model C5/CBT7, now with connections on RIGHT hand side. Controls 2 speed main pump and air blower, plus light, and receptacle for an ozonator too, with pump power cord, blower cord, light cord, users manual, and digital topside display. A very nice replacement control works on most any hot tub or portable spa, replacing your old control and heater. Includes stainless steel high flow 5kw heater, 15 long, standard size. From Spa Pumps And More. A very complete kit with topside and 5 cords for pump, blower, topside, temp sensor, and light. More info at Spa Pumps And More. This makes the unit fully self-contained, so you won’t have to locate the temp sensor yourself, saves time! Message us though, please. This CBT7 Control comes with 5kw 15″ high flow heater, 2.5×5.0″ Topside display/keypad, pump and blower and light cords, and is a complete unit to replace your old spa control and heater. Topside drops into a 1-3/4 round cutout in your spa. Intended for use under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. Runs a main 2 speed spa pump, and an air blower or 2nd pump, and spa light, and has a receptacle for ozonator or ionizer or any other non-switched device. Comes with new power cords for your main 2-speed pump and an air blower or second pump, and a light, with quick disconnect plugs to the control. Temperature sensor comes with a long cord so you can either mount the sensor onto the heater, or, mount it in your tub if your tub has a drywell, has provision for a remote temp sensor. Cord is 8 feet long, but again it is your choice to mount it right on the heater or stick the sensor into a tub fitting you already have. Includes 15 inch long stainless steel high flow 2 heater, with 5kw Incoloy element. Can be used on 115/120v or 230/240 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The CBT7 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115/120v or 230/240v. On a 115/120 volt source, the heater will be 1.25kw or 1250 watts. From the factory the CBT7 is set for 230/240v incoming power, 230/240v to the heater, and 230/240v to the pump. 115/120v to the air blower, and 12 volts to the light. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by United, and ready to go as is. Control box stands 11.1″ tall, and 15.5″ wide, 3.4″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By United Spas, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by United Spas. United has been building digital hot tub controls over 20 years. CBT7 Digital Control by United Spas model C5. 15″ stainless steel high flow 5kW heater with standard threaded couplings for 2″ PVC plumbing. Digital display keypad (topside) 2.5×5.0 with 9.5 foot long cord. Drops into 1-3/4 round cutout. One pump power cord 4-wire for a 2-speed pump, 45 long with quick disconnect AMP plug and motor connectors. Air Blower power cord 57 with quick disconnect AMP plug, 18/3 wire size. Light cord with quick disconnect AMP plug, 8 foot long. Temperature sensor and cord. United Spas t& Topside Installation Manual & User’s Guide. United Spas C5 Series Installation & Service Manual. Additional info: Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. The item “Hot Tub Heater Control Digital Spa Controller Pack C5-B United Spas CBT7 C5B new” is in sale since Sunday, September 30, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “spapumpsandmore” and is located in Los Angeles, California. This item can be shipped to United States.

  • Controls: main pump, air blower, light, option for ozone and
  • Voltage: 240 volt or 120 volt, changeable
  • Heater Size: High Flow 2″ 15 inch
  • Warranty: Factory Warranty by United Spas
  • Display: Digital Topside Keypad 5×2.5″
  • Model: C5
  • Modified Item: No
  • Country/Region of Manufacture: United States
  • Custom Bundle: No
  • Dimensions: 11.1Tx15.5Wx3.4″D
  • Includes: Power Cords, Manuals
  • Intended Use: For portable spas, mounted under redwood skirt.
  • Distributed By: Spa Pumps And More
  • Type: Pump, Blower & Light
  • MPN: CBT7
  • Brand: United Spas
  • Non-Domestic Product: No
Balboa BP501 Retro Fit Kit- Spa Pack with TP600 Controller and cables
Jan 17th, 2019 by admin
Balboa BP501 Retro Fit Kit- Spa Pack with TP600 Controller and cables


Balboa BP501 RetroFit Kit. Made in America. Includes TP600 Top Side Controller. Optional – Integrates with you iPhone, iTouch, Pad. The BP Series is the 1st in a newly designed and improved plat form that focuses on reliability. The BP501 uses a more advance carbon bases casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. This is a retrofit kit and is designed to replace a complete spa pack with any other manufactures hot tub heating system such as Gecko, Colman, Hydro Quip, Spa Guts, Arctic Spa, LA Spas, Beach Comber, Sundance, Emerald Spas, Maxx Spa, Hydro Spa, Hot Spring to name a few. The retrofit kit comes complete with the TP600 digital top side controller, and a set of cables for two pumps, and an ozone. Detailed retrofit instructions are also included so that a spa owner can quickly change over to BALBOA the world leader in Spa Heaters. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). And it now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). Although this spa pack can work at 120 VAC in which case it will produce 1.5 Kw of heat, it is primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s union tail pieces (included) fit standard 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day , various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 1 x 2-speed pump1, 1 x 1-speed pump2, Ozonator, 12v Light. 1 x 1-speed pump1, 1 x 1-speed pump2, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed pump1, 1 x 1-speed blower, Ozonator, 12v Light. 1 x 1-speed pump1, 1 x 1-speed blower, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed pump1, Ozonator, 12v Light. 1 x 1-speed pump1, Circulation Pump, Ozonator, 12v Light. 1 x 2-speed 120v pump1, 120v Ozonator, 12v Light. 1 x 1-speed 120v pump1, 120v Circulation Pump, 120v Ozonator, 12v Light. 1 x 2-speed pump1, Circulation Pump, Ozonator, 12v Light. Setup 1-6 use 240v, pumps, blower and ozonator, although some field jumpers are available to mix 240 and 120 device. Connection for Audio/Visual components power (120 volt) is available as are connections to control auxiliary heater. 10.56″ High x 17″ Long x 4.8 Deep. Includes PN# 50056 TP600 Totpside Controller with warm, cool, light, jets overlay. Includes: 2 sets of pump cables and an ozone cable with AMP connector for Balboa Spa Pack. Includes: Detailed instruction manual for installation to replace another brand of Spa Heater. 120 or 230 VAC ozone support (circ pump and ozone must have same voltage). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 4.0kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E14 or others made by Grundfos or Waterway Mighty-Might. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Balboa TP600 with warm, cool, light, jets1, jets2, flip button. Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store! The item “Balboa BP501 Retro Fit Kit- Spa Pack with TP600 Controller and cables” is in sale since Friday, February 19, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.

  • UPC: 682318838249
  • Brand: Balboa
  • MPN: Kit-Retrofit–BP501-TP600
Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230
Jan 7th, 2019 by admin
Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230


Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230


Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230


Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230


Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230


15″ 5.5kw High-Flow Heater, 3.25 x 7.25″ Digital Topside Display/Keypad (or optional 2.5 x 5.5 Topside Display/Keypad if you request this). Rated for 230 volts 4-wire incoming power or 115 volts, it is changeable. From Spa Pumps And More. This Smartouch Digital Control comes with 15 hi-flow heater, Topside display/keypad, power cords, and is a complete unit to replace your old spa control and heater. 3.25 x 7.25″ topside drops into 2.2×6.2″ cutout in your spa, see 2nd photo. The smaller one is 2.5×5.5″ and drops into a 1.7×4.7″ cutout hole. For 4-wire 240 volts or 3-wire 115 volts sources only. The listed unit is not for 3-wire 230v; please message if you need 3-wire 230. 3-wire is less common and is built to order, takes an extra days time, just message us if you want 3-wire, please. More info at Spa Pumps And More. A power source from the house that is 4-wire has a true neutral, a ground, and 2 hots. 4-wire may be branched to provide 230v to devices as well as provide 115v to other devices, via the Neutral wire. A European style 3-wire power source has no neutral, and only a ground wire and 2 hot wires, and can not provide 115 volts to any device therefore 3-wire systems are limited to being all 230 volts. This is a high flow system for 1-1/2″ or 2″ pvc pipe size plumbing systems and requires a minimum flow of 20 GPM , it is NOT for low flow systems with 3/4″ or 1″ plumbing. This high flow heater can NOT be modified to work on low flow plumbing. Runs a main 2 speed spa pump, and an air blower (or 2nd single speed pump), and spa light, and has an output for ozonator or ionizer or any other non-switched device. Comes with a new power cord for your main 2-speed pump, with quick disconnect plug to the control. You also get quick disconnect plugs and short’pigtail’ cords for the air blower, spa light, and one accessory device, like an ozonator. These are short cords meant to splice to your existing light cord, blower cord, and ozonator cord, using wire nuts. Includes 15 inch long x 2.25 diameter 5500 watt stainless steel high flow heater, can be used on 115v or 230 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The Smartouch SMTD 1000 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115v or 230v. On a 115 volt source, the heater will be 1.4kw or 1375 watts. From the factory the SMTD1000 is set for 230v incoming power, 230v to the heater, and 115v to the pump, air blower (or second 1-speed pump), and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. Intended to be mounted under the redwood skirt of a portable spa, not out in the rain, please note. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by ACC, and ready to go as is. Control box stands 14.6″ tall, and 15.4″ wide, 5″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By ACC, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by Applied Computer Controls. ACC has been building digital hot tub controls over 30 years. Smartouch Digital Control by ACC model SMTD1000. 15 stainless steel flow-through heater with standard threaded couplings. Digital display keypad (topside) 3.25×7.25″ with 57″ long cable. Extension cords available at extra cost, message us please. Pump 4 wire power cord with quick disconnect AMP plug and motor connectors. 4-wire is Neutral, Ground, L1, L2. Air Blower pigtail with quick disconnect AMP plug, 18/3 wire size, to splice to existing blower cord. Ozonator 7 pigtail with quick disconnect AMP plug, 18 gauge wire. Light 7 pigtail with quick disconnect AMP plug, 18 ga wire. ACC User’s Manual (can be viewed on the ACC-spas website if you care to). Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. PROGRAMMING GUIDE and Wiring Diagrams can also be viewed on the ACC-spas website if you are interested. So message us if you want 3-wire and we’ll respond with cost and leadtime. The item “Spa Control Hot Tub Heater Digital Controller Pack L SMTD1000 ACC 5.5kw 115/230″ is in sale since Sunday, September 30, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “spapumpsandmore” and is located in Los Angeles, California. This item can be shipped to United States.

  • Country of Manufacture: United States
  • Controls: Pump & Blower or 2 pumps, light, heater, ozonator
  • Shape: For 2″ or 1-1/2″ pvc pipe size systems
  • Voltage: 240V or 120V convertible
  • Heater Size: 15″ long x 2.25″ outside diameter w/ 2″ pvc unions
  • Model: SMTD1000
  • MPN: smtd1000
  • Country/Region of Manufacture: United States
  • Brand: Spa Pumps And More
  • Includes: all new power cords
  • Warranty: ACC factory warranty.
  • Type: HIGH FLOW Heater 20 GPM Minimum
Balboa VS501 Retrofit Kit Spa Heater with cables, light, VL401 LCD controller
Jan 5th, 2019 by admin
Balboa VS501 Retrofit Kit Spa Heater with cables, light, VL401 LCD controller



Balboa Spa Pack VS501 Retrofit Kit. Comes with VL401 LCD Controller. Replaces Most Spa Packs. OEM Bundle 54217-Z with Upgrades. Balboa VS501z 5.5-1.5 Kw Digital Spa Pack With Patented M7 technology – This is the world’s best spa pack! – Made in America. Time to upgrade your old spa pack hot tub heater? Balboa VS501z , uses simply the best spa pack technology in the market. Completely digital circuitry means less failures, more accurate heating range, and much simpler to use. Accurate to +/- 1 degree with full top side LCD controllers , means, you will never have to leave the spas or tub to change the temperature. TheVL 401 LCD controller is more costly than the LED style VL403 controllers however it provides much better lumination durring the day. As such all our Spa Pack come standard with the upgrade to LCD controller. The Balboa Spas Pack works at either 120 VAC producing 1.5KW, or with a change of a jumper operates at 230 VAC producing 5.5 KW of heat. It fits any standard 2″ or 1 1/2″ plumbing making it ideal to upgrade almost any older mechanical spa pack. Replaces any Spa Pack from other manufactures! Don’t be fooled , Balboa Spa Packs can replace any hot tub heater on the market including Gecko, Hot Springs, Len Gordon, Hydro Quip, LA Sas, Cal Spas, Coleman Spas, Beachcomber Spas, Artic Spas to name a few….. Built in programmable features such a cycle programming, sleep mode, economy mode and self diagnosis are just some of its features. Weather freeze ups are eliminated with the built in freeze protection system. It also has the ability to select how much current will be drawn allowing use of a 30 Amp breaker or 40 Amp, yet still deliver the full features. It has receptacles for the following. One 2-speed pump + one 1-speed pump or blower (not both)+ one circulation pump + one ozonator + one constant-on for Audio/Visual devices + one 12 volt light. All receptacles (except light) can be switched to supply 120 Volts or 230 Volts. VS501Z pack including Stainless Steel portable heater with 2 heater tail pieces. 4 button LCD light duplex digital control VL401 with 7′ cable. One 4-wire 2-speed pump cable with AMP plug. One 3-wire pump/blower cable with AMP plug. One 12 volt light wiring assembly with AMP plug. One loose 4-pin AMP plug with pins (to adapt a non-Balboa ozonator). Plasticized control instruction sheet; complete instruction manual for retrofit situations produced by Northern Lights. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before, after the pump or before or after the filter). What is the difference between a regular VS501 and VS 501Z? Only the VS501(Z) is able to run either 220 VAC or 120 VAC accessories or a mixed combination! The latter & older models require accessories such as ozone to be the same voltage as the primary pump, limiting their applications. The VS501z is the most current model line from Balboa. The LCD digital topside control includes light function, high low pump, temp control, and blower. Functions may be changed to Temp Up, Temp Down, Jets, and Light. 10.56″ High x 19.5″ Long x 4.60 Deep. Comes with 12 V light that will support LED lighting. UL, CSA, and CE certification. 120 or 220 VAC ozone support. NOTE you can only use a 2nd single-speed pump or blower not both! If small circulating pump is being used the flow through heater must deliver 23 USGPM or more. MADE IN AMERICA not China. Measurements: W=6.3″ (16cm) , H=2.2″ (5.58cm). If you are looking for the best most reliable tub replacement system on the market, then Balboa VS501z with M7 technology it is. Their unsurpassed reliability is why Balboa is the world leader in Spa Pack manufacturing both in quality and reliability. Balboa Spa Pack Features. 5.5 Kw Heater 220 VAC. Separate Optional Aux 5.5 Kw Heater. 240 VAC or 120 VAC. 120/240 Volt output receptacle. Separate voltage for ozone & blower. 2 -Speed Pump 1. 1-Speed Blower or Pump 3. Light switchable to 12 volt or 120 VAC. Fiber Optic Wheel Light. Standard, Economy, Sleep Mode. 12 hour filter cycle. 24 hour filter cycle. Filter cycle program by time of day. Clean up cycle (filter & ozone on after use). Only when jets are on. IR Dolphin Remote Control Option (short range). RF Station Wireless Remote Control (long range). Wireless PC Remote Control via USB. Tech Support 1 800 by NLCT. Your #1 Hot Tub Parts Replacement Store! The item “Balboa VS501 Retrofit Kit Spa Heater with cables, light, VL401 LCD controller” is in sale since Friday, February 19, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hot-tub-parts” and is located in Winnipeg, Manitoba. This item can be shipped to United States, Canada.

  • UPC: 608819222844
  • Brand: Balboa
  • MPN: Kit-Retrofit-VS501-VL401
Dream Maker Spas Digital Topside Controller & Overlay Decal
Dec 26th, 2018 by admin
Dream Maker Spas Digital Topside Controller & Overlay Decal


Dream Maker Spas Digital Topside Controller & Overlay Decal


For Dream Maker Spas. Measures 5.25 across. Overlay Sticker Part # 407011. We sell additional Dream Maker Spa parts. Please send message with any questions / inquiries. The item “DREAM MAKER SPAS DIGITAL TOPSIDE CONTROLLER & OVERLAY DECAL” is in sale since Tuesday, January 2, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “ecommercespashop” and is located in Tampa Bay, FL. This item can be shipped to United States.

  • MPN: 407012
  • Brand: DreamMaker Spa
»  Substance: WordPress   »  Style: Ahren Ahimsa