Applied Computer Controls, ACC Top Side Keypad/Display model KP-2010 fit spa control systems by ACC including the ePack, SMTD1000, SMTD1500, Compack Junior. Ribbon cable attached is 5 feet long. From Spa Pumps And More, please check out our other great deals. KP-2010 top side keypad/display, it is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. You will receive the 3.25″ x 7.25″ if you order from this listing. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL HOT TUB HEATER CONTROLLER ACC KP-2010 Top Side Keypad/Display NEW” is in sale since Saturday, May 18, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “spapartsdistributor” and is located in Los Angeles, California. This item can be shipped to United States.
Retrofit hot tub electronic system. Will operate 1 dual speed pump, 1 single speed pump, light 12v, ozonator. Runs on 115v OR 240v AC. The item “Spa Control Hot Tub Heater Controller Pack SMTD1000 KP-2010 ACC 5.5kW 230/115v” is in sale since Sunday, November 11, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “hottubsrus” and is located in Brentwood, Tennessee. This item can be shipped to United States.
Spa Control Hot Tub Heater Controller Pack SMTD1000 Big Topside NEW 115/230v ACC. Ships from Spa Pumps And More. The SMTD1000 is unique, unlike other spa controls it does not rely on small motherboard relays to carry the 23 amp load to the heater, it has a large contactor switching the heater, see inset photo. This eliminates the most common cause of board failure, having the heater relay fail. A great feature that only the SMTD 1000, 2000, and 3000 controls have. This Smartouch Digital Control comes with 15″ high flow 2″ heater, Large 3.25×7.25 Topside display/keypad, power cords, and is a complete unit to replace your old spa control and heater. Drops into 2.2×6.2 cutout in your spa. Runs a main 2 speed spa pump, and an air blower, and spa light, and has an output for ozonator or ionizer or any other non-switched device. Intended use is to be mounted under the redwood skirt of a typical portable spa, not outside in the rain, snow, etc. Runs on 20 GPM minimum , 2″ or 1-1/2″ PVC pipe size. This is NOT a circ pump system for tiny 24/7 3/4 pumps. This is for conventional 2-speed pump and is a high flow heater and control system. Message us if you need a tiny circ pump controller, along with all your specs and details. This control above is NOT for low flow circ systems. Comes with a new power cord for your main 2-speed pump, with quick disconnect plug to the control. You also get quick disconnect plugs and short’pigtail’ cords for the air blower, spa light, and one accessory device, like an ozonator. These are short cords meant to splice to your existing light cord, blower cord, and ozonator cord, using the supplied wire nuts. Includes 15 inch long 5500 watt (5.5kw) stainless steel heater, can be used on 115v or 230 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The Smartouch SMTD 1000 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115v or 230v. On a 115 volt source, the heater will be 1.4kw or 1375 watts. From the factory the SMTD1000 is set for 230v incoming power, 230v to the heater, and 115v to the pump, air blower (or second pump), and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems, comes with 2″ sockets which you can easily bush down to 1-1/2″ using pvc bushings from your plumbing store. Control is intended for use under the redwood skirt of a portable spa, not outside in the rain please note. This control is for 4-wire 230v or for 115v. IF you need a control for 3-wire 230v, an all 230v system, we can supply it, takes an extra day or so, message us and we’ll respond with price and leadtime. So message us if you want 3-wire, please. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by ACC, and ready to go as is. Control box stands 14-9/16″ tall, and 15-3/8″ wide, 7″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By ACC, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by Applied Computer Controls. ACC has been building digital hot tub controls over 30 years. Message us anytime for tech support, questions, or just general help, or we’re happy to call you if you want to chat. Smartouch Digital Control by ACC model SMTD1000. 15 stainless steel heater with standard threaded couplings. Large digital display keypad (topside) 3.25×7.25″ with 57″ long cable. Pump 4 wire power cord with quick disconnect AMP plug and motor connectors. Air Blower power cord, a short’pigtail’ with quick disconnect AMP plug, 18/3 wire size, to splice to existing blower cord. Ozonator cord, a short pigtail with quick disconnect AMP plug, 18 gauge wire. Light pigtail with quick disconnect AMP plug, 18 ga wire. ACC User’s Manual. Manual and Programming Guide can be viewed and printed on the ACC-Spas website. The item “Spa Control Hot Tub Heater Controller Pack SMTD1000 KP-2010 ACC 5.5kW 230/115v” is in sale since Sunday, July 7, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “tazi_discounts” and is located in Los Angeles, California. This item can be shipped to United States.
NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. Comes with KP-2010 top side keypad/display, it is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. You will receive the 3.25″ x 7.25″ if you order from this listing. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. It is NOT for tiny 3/4 circ pumps. For low flow controls and pumps check out our other listings as we do have them, thanks, Spa Pumps And More. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Check out my other items. Be sure to add me to your favorites list. The item “SPA CONTROL PACK HOT TUB HEATER CONTROLLER ePack ACC KP-2010 4kW 115/230v NEW” is in sale since Wednesday, May 29, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “spapumpsandmore” and is located in Los Angeles, California. This item can be shipped to United States.
This listing includes a free LED-10 light bulb, a color changing bulb to add some fun to your tub! Spa Control Hot Tub Heater Controller Pack SMTD1000 Big Topside NEW 115/230v ACC. The SMTD1000 is unique, unlike other spa controls it does not rely on small motherboard relays to carry the 23 amp load to the heater, it has a large contactor switching the heater, see inset photo. This eliminates the most common cause of board failure, having the heater relay fail. A great feature that only the SMTD 1000, 2000, and 3000 controls have. This Smartouch Digital Control comes with 15″ high flow 2″ heater, Large 3.25×7.25 Topside display/keypad, power cords, and is a complete unit to replace your old spa control and heater. Drops into 2.5×6.5 cutout in your spa. Runs a main 2 speed spa pump, and an air blower, and spa light, and has an output for ozonator or ionizer or any other non-switched device. Intended use is to be mounted under the redwood skirt of a typical portable spa, not outside in the rain, snow, etc. Runs on 20 GPM minimum , 2″ or 1-1/2″ PVC pipe size. This is NOT a circ pump system for tiny 24/7 3/4 pumps. This is for conventional 2-speed pump and is a high flow heater and control system. Message us if you need a tiny circ pump controller, along with all your specs and details. This control above is NOT for low flow circ systems. Comes with a new power cord for your main 2-speed pump, with quick disconnect plug to the control. You also get quick disconnect plugs and short’pigtail’ cords for the air blower, spa light, and one accessory device, like an ozonator. These are short cords meant to splice to your existing light cord, blower cord, and ozonator cord, using the supplied wire nuts. Includes 15 inch long 5500 watt (5.5kw) stainless steel heater, can be used on 115v or 230 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The Smartouch SMTD 1000 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115v or 230v. On a 115 volt source, the heater will be 1.4kw or 1375 watts. From the factory the SMTD1000 is set for 230v incoming power, 230v to the heater, and 115v to the pump, air blower (or second pump), and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. Control is intended for use under the redwood skirt of a portable spa, not outside in the rain please note. This control is for 4-wire 230v or for 115v. IF you need a control for 3-wire 230v, an all 230v system, we can supply it, takes an extra day or so, message us and we’ll respond with price and leadtime. So message us if you want 3-wire, please. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by ACC, and ready to go as is. Control box stands 14-9/16″ tall, and 15-3/8″ wide, 7″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By ACC, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by Applied Computer Controls. ACC has been building digital hot tub controls over 30 years. Message us anytime for tech support, questions, or just general help, or we’re happy to call you if you want to chat. Smartouch Digital Control by ACC model SMTD1000. 15 stainless steel heater with standard threaded couplings. Large digital display keypad (topside) 3.25×7.25″ with 57″ long cable. Pump 4 wire power cord with quick disconnect AMP plug and motor connectors. Air Blower power cord, a short’pigtail’ with quick disconnect AMP plug, 18/3 wire size, to splice to existing blower cord. Ozonator cord, a short pigtail with quick disconnect AMP plug, 18 gauge wire. Light pigtail with quick disconnect AMP plug, 18 ga wire. ACC User’s Manual. Manual and Programming Guide can be viewed and printed on the ACC-Spas website. The item “Spa Control Hot Tub Heater Controller Pack SMTD1000 KP-2010 ACC 5.5kW Free LED” is in sale since Wednesday, August 8, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “tazi_discounts” and is located in Azusa, California. This item can be shipped to United States.
