4 pack – Guardian Pool Filter 717-145-04 : Replaces Pleatco PA56L, Hayward C2030. Each filter is brand new sealed! Thank you for looking.
More info at Spa Pumps And More. NEW hot tub controller, with electric high flow 2″ heater, by Applied Computer Controls, ACC model’ePack’ SMTD1500, complete, with set of power cords (pigtails) for a main 2-speed pump, air blower, light, and ozonator, for standard 4-wire 230 volt incoming power, or, for 115 volt, it is convertible for voltages, 15″ stainless steel high flow heater, 2 pipe size couplings, standard threaded split nuts 4.0kw heater, see photos for dimensions. Temperature probes are built in to heater, so no external mess with extra wires, probes in the tub, etc. Main control box is 11.5″Tx14″Wx4.5D approximately. From Spa Pumps And More, please check out our other great deals. For more information look at Spa Pumps And More. Their part number is SMTD1500. Alternate part number is ePack. Model: ePack SMTD 1500. Display: Digital Topside Keypad 3.25″ x 7.25″. Heater: High Flow 2 15 inch 4kw. Dimensions: 11.5T x 14W x 4D. Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower OR second pump, and Light. Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. Comes with KP-2010 top side keypad/display, it is 3.25″ x 7.25″ and drops into a 2.2″ x 6.2″ cutout. You will receive the 3.25″ x 7.25″ if you order from this listing. For repairing your spa, better and less costly than replacing parts on an old control, fits for most any spa or hot tub except for maybe some of the tiny 1 person tubs. Nice big clear display. Not refurbished, but all new! The ePack will run one main 2-speed pump, filtering and heating on low speed, and jet action on high speed. Also runs an air blower on-off, OR, any other device on-off, for example a secondary single speed pump. And a 12 volt light, and it has output to an non-switched auxiliary device such as an ozonator, and of course it powers and controls the heater included. Factory default settings are. Incoming power 230v 4-wire (can be 115v). High Flow 2 Heater 230v (can be 115v). Main 2-speed pump 115v (can be 230v). Air Blower 115v (can be 230v) (or can be the on-off for a second pump). Ozonator 115v (can be 230v). Light 12 volts only. If you need to control more than this, look at the Model 2000, the SMTD2000 control we list here. Note: intended use is for mounting under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. This is a high flow heater and control, 20 GPM minimum, for 2″ or 1-1/2″ PVC pipe size. This model is NOT for tiny 3/4 circ pumps. For low flow controls and pumps go to Spa Pumps And More and give them all your details. Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. Look at Spa Pumps And More for further details.
More info at: Spa Pumps And More. A very nice replacement control works on most any hot tub or portable spa, replacing your old control and heater. Includes stainless steel high flow 5.5kw heater, 15 long, standard size. Nice large contactor in the SMTD2000 switches the 24 amp heater on-off, this is a huge advantage over all other control brands that have a tiny relay on the motherboard to do the switching. For more information look at Spa Pumps And More. Their part number is SMTD2000. Display: Digital Topside Keypad 3.25×7.25. Heater: High Flow 2 15 inch 5kw. Dimensions: 14.5T x 15.4W x 5.5″D (5.5″ deep if you include the mounting feet, the deepest part). Voltage: 240V 4-wire standard. Convertible to 115V optional. Country of Manufacture: United States. Type: Pump, Air Blower, Light, and a second pump (which can be a 2-speed). Brand: Applied Computer Controls (ACC). Intended Use: For portable spas, mounted under redwood skirt. UPC: Does not apply. Additional detail from Spa Pumps And More. This Smartouch Digital Control comes with 5.5kw 15″ heater, Large 3.25×7.25″ Topside display/keypad, power cords, and is a complete unit to replace your old spa control and heater. Topside drops into 2.2×6.2 cutout in your spa. Intended for use under the redwood skirt of a typical portable spa, not out in the rain, snow, etc. Runs a main 2 speed spa pump, and a second pump (can be a 2-speed or single speed), and an air blower or 3rd pump, and spa light, and has an output for ozonator or ionizer or any other non-switched device. This large relay takes the load of the heater off the motherboard and is a major advantage over other spa controls. Comes with new power cords for your main 2-speed pump and second pump, with quick disconnect plugs to the control. You also get quick disconnect plugs and short’pigtail’ cords for the air blower, spa light, and one accessory device, like an ozonator. These are short cords meant to splice to your existing light cord, blower cord, and ozonator cord, using wire nuts. Includes 15 inch long stainless steel high flow 2 heater, with 5.5kw Incoloy element. Can be used on 115/120v or 230/240 volts, it’s changeable voltage-wise. This is the common length of heater for 98% of hot tubs out there, comes with industry-standard black plastic split nuts with common buttress threads, so can couple right up to your existing plumbing if you have a 15 heater now. The Smartouch SMTD 2000 can run off your 4-wire 230 volt supply voltage or off of a 3-wire 115 volt household power. Also, the pump and blower voltages can be changed to either 115/120v or 230/240v. On a 115/120 volt source, the heater will be 1.4kw or 1375 watts. From the factory the SMTD2000 is set for 230/240v incoming power, 230/240v to the heater, and 230/240v to the pumps. 115/120v to the air blower, and the ozonator, and 12 volts to the light, which is industry-standard. Or, you can change the voltages yourself, it is easy. Can be mounted in any direction or position, even upside down, and the water can flow either direction through the heater. Can be fitted to 1-1/2″ or 2″ PVC pipe size systems. User’s Manual shows how to program changes into the control, but it is factory programmed, and tested by ACC, and ready to go as is. Control box stands 14.6″ tall, and 15.4″ wide, 5.5″ deep, heater is 15″ flange to flange. Designed, built and tested in the U. By ACC, a rugged, proven, spa control, good tech support, good parts availability, made in California. Not refurbished, rebuilt, demo, all is brand new in factory packaging, warranted and backed by Applied Computer Controls. ACC has been building digital hot tub controls over 30 years. Smartouch Digital Control by ACC model SMTD2000. 15″ stainless steel high flow heater with standard threaded couplings for 2″ PVC plumbing. Large digital display keypad (topside) 3.25×7.25″ with 57″ long cable. (Extension cords available at extra cost) Drops into 2.2×6.2 cutout. Two (2) pump 4-wire power cords, 48 long with quick disconnect AMP plugs and motor connectors. Air Blower power cord 3 foot with quick disconnect AMP plug, 18/3 wire size, to splice to existing blower cord. Ozonator pigtail with quick disconnect AMP plug, 18 gauge wire. Light pigtail with quick disconnect AMP plug, 18 ga wire. Additional info: Warranties: all warranties are from the manufacturers who made the goods, not from the distributors, dealers, or resellers. Heater warranties do not cover running with air in the system (dry-fire) and burning a heating element, as this is not a defect. Pump warranties do not protect against seals being scratched by debris and leaking. Standard stuff, but just fyi, so you are aware. More info at Spa Pumps And More.
Hot Springs Black Control pack as is.
Balboa BP501 Spa Pack – Hot Tub Heater-56485-05 With Wireless Controller. Comes with a good used spa controller that need a the cord spliced back together.
Made in America. Integrates with you iPhone, iTouch, Pad, or Android! The BP Series is the 1st in a newly designed and improved platform that focuses on reliability. The BP501 uses the same Zircaloy or Titanium heater elements as used in the VL and EL series spa pack. The new BP501 utilizes a more advance carbon based casing that is highly flame retardant and impact resistant. New Features such as quick disconnect heater elements, Wi-Fi Ready, and Press and Hold topside navigation buttons. The BP Series uses M7 Technology which is simply the best spa pack technology on the market. Completely digital circuitry means less failure, more accurate heating range (+/- 1 degree F). The BP Series now includes both a high range (80-104F) and a low range (50-99 F) operation. The Patented M7 Technology removes the need for pressure sensors and remote heat sensors common on other older spa packs. This unique technology allows the spa pack to be positioned in any location or direction (before or after the pump or before or after the filter). This spa pack can work at 120 VAC in which case it will produce 1.4 Kw of heat. It is however primarily expected that it will be used at 230 VAC (requiring 30-50 AMP service) and will produce 5.5 kW of heat. One or more auxiliary heater, each producing 4.0 kW or 5.5kW can be slaved to the unit if more power is required. It’s standard spa pack union tail pieces fit 2″ piping or with reducers can be easily adapted to 1.5″. Built in programmable features such a 12 or 24 hour filter cycle programming by duration or time of day, various power saving modes including standard, economy, and standard in economy mode, ozone suppression, clean up cycle, freeze protection, panel lock, temperature lock, standby mode for filter changes and sophisticated diagnosis and reminder measures are just some of the features. It also has the ability to select how much current will be drawn allowing a breaker as low as 30 Amp, yet still deliver the full 5.5 kW of electric heat. It has receptacles for the following. 10.56″ High x 17″ Long x 4.8 Deep. Requires Balboa TP series panels and has connectors for 1 main panels and 1 auxiliary panels. Optional Wi-Fi Module for use with iPhone, iPad, iPod, or Android device. 120 or 230 VAC ozone support (ozone must have same voltage as heater pump). High or Low current mode. The flow through heater tube must be a minimum of 20 USGPM if the heater is 5.5kW. This flow rate should be checked if your spa uses a small circulation pump such a Laing E10 or others made by Grundfos or Waterway. These small pumps when used with 1 piping typically cannot produce this flow. MADE IN AMERICA not China! Works with the following Balboa Top Side Controllers. Balboa TP600, Balboa TP400, TP600, TP900. Wi-Fi Module- PN 50350. Your #1 Hot Tub Parts Replacement Store!
SPA FROG Serene Mineral Cartridge 01-14-3812 (3 pack). FROG Serene Mineral Cartridges (formerly Spa FROG) are for use in the FROG Serene Floating Systems, in which pre-filled mineral and bromine cartridges combine in a floating dispenser to give any spa or hot tub crystal clear water with a silky feel. FROG Serene Mineral Cartridges snap easily into a reusable floating holder and when used in combination with the FROG bromine cartridge, reduces the need for bromine by up to 50%. FROG Serene Mineral Cartridges last an average of four months.
Handi Spa Hot Tub Plastic Resin Base Pad – Confer SP3248 Deck Foundation (3 Pack). 6 x 23 x 49 inches. Protect the underside of your hot tub or spa and speed up installation with the Confer SP3248 Handi Spa Hot Tub Deck Foundation Plastic Resin Base Pad. These durable base pad mats provide a cushion between rough-surfaced wood decks and concrete pads or create a new foundation wherever you want. Durable Material: The Confer SP3248 Handi Spa Hot Tub Deck Foundation Plastic Resin Base Pad is made of durable plastic resin material that is designed to withstand the elements and provide long-lasting performance. Large Size: Each mat measures 32 x 48 inches, making it easy to create an 8 x 8-foot pad with 6 pads. This large size is perfect for most hot tubs or spas and provides ample space for installation. Easy Installation: The Confer SP3248 Handi Spa Hot Tub Deck Foundation Plastic Resin Base Pad features built-in connectors that quickly lock the pads together for greater strength and reduced shifting. This makes installation a breeze and ensures a stable foundation for your hot tub or spa. Versatile: The versatility of the Confer SP3248 Handi Spa Hot Tub Deck Foundation Plastic Resin Base Pad allows it to be used under pool filter equipment, plastic sheds, under trash cans, and inside the garage. This makes it a versatile product that can be used in a variety of applications. Product Name: Confer SP3248 Handi Spa Hot Tub Deck Foundation Plastic Resin Base Pad (3 Pack). Size: Each mat measures 32 x 48 inches; 6 pads create an 8 x 8-foot pad. Installation: Built-in connectors quickly lock pads together for greater strength and reduced shifting. Versatility: Can be used under pool filter equipment, plastic sheds, under trash cans, and inside the garage. The Confer SP3248 Handi Spa Hot Tub Deck Foundation Plastic Resin Base Pad is an excellent choice for anyone looking to protect their hot tub or spa and speed up installation. With its durable material, large size, easy installation, and versatility, this product is sure to provide long-lasting performance and reliable protection for your hot tub or spa. We are always working hard to ensure your package arrives as soon as possible. We do not accept P. Please provide a physical address.
3 Pack King Technology Spa Frog Serene Mineral Replacement Cartridge 01-14-3812. Refill for use in either the spa frog floating system, or for users of the spa frog inline system. Use with companion frog bromine cartridge. Spa frog mineral cartridge. For more info contact. Mark’s Pool Store. Over 30 Years Experience. Spa Frog Mineral Cartridge refill for use in either the Spa Frog Floating System, or for users of the Spa Frog Inline System which is factory-installed in the spa. Use with companion Frog Bromine Cartridge. Answer them in a timely manner. Thank you for looking.. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “markspoolstore1″ and is located in this country: US. This item can be shipped to United States.
Balboa water group® OEM spa pack circuit board digital part # 55000-04 model # TS2000. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jamesrogers2020″ and is located in this country: US. This item can be shipped to United States, New Zealand, Fiji, Papua New Guinea, Wallis and Futuna, Gambia, Malaysia, Taiwan, Poland, Oman, Suriname, United Arab Emirates, Kenya, Argentina, Guinea-Bissau, Armenia, Uzbekistan, Bhutan, Senegal, Togo, Ireland, Qatar, Burundi, Netherlands, Slovakia, Slovenia, Equatorial Guinea, Thailand, Aruba, Sweden, Iceland, Macedonia, Belgium, Israel, Liechtenstein, Kuwait, Benin, Algeria, Antigua and Barbuda, Swaziland, Italy, Tanzania, Pakistan, Burkina Faso, Panama, Kyrgyzstan, Switzerland, Djibouti, Chile, China, Mali, Botswana, Republic of Croatia, Cambodia, Indonesia, Portugal, Tajikistan, Vietnam, Malta, Cayman Islands, Paraguay, Saint Helena, Cyprus, Seychelles, Rwanda, Bangladesh, Australia, Austria, Sri Lanka, Gabon Republic, Zimbabwe, Bulgaria, Czech Republic, Norway, Côte d’Ivoire (Ivory Coast), Kiribati, Turkmenistan, Grenada, Greece, Haiti, Greenland, Yemen, Afghanistan, Montenegro, Mongolia, Nepal, Bahamas, Bahrain, United Kingdom, Bosnia and Herzegovina, Hungary, Angola, Western Samoa, France, Mozambique, Namibia, Peru, Denmark, Guatemala, Solomon Islands, Vatican City State, Sierra Leone, Nauru, Anguilla, El Salvador, Dominican Republic, Cameroon, Guyana, Azerbaijan Republic, Macau, Georgia, Tonga, San Marino, Eritrea, Saint Kitts-Nevis, Morocco, Saint Vincent and the Grenadines, Mauritania, Belize, Philippines, Democratic Republic of the Congo, Republic of the Congo, Colombia, Spain, Estonia, Bermuda, Montserrat, Zambia, South Korea, Vanuatu, Ecuador, Albania, Ethiopia, Monaco, Niger, Laos, Ghana, Cape Verde Islands, Moldova, Madagascar, Saint Pierre and Miquelon, Lebanon, Liberia, Bolivia, Maldives, Gibraltar, Hong Kong, Central African Republic, Lesotho, Nigeria, Mauritius, Saint Lucia, Jordan, Guinea, Canada, Turks and Caicos Islands, Chad, Andorra, Romania, Costa Rica, India, Mexico, Serbia, Kazakhstan, Saudi Arabia, Japan, Lithuania, Trinidad and Tobago, Malawi, Nicaragua, Finland, Tunisia, Uganda, Luxembourg, Brazil, Turkey, Germany, Egypt, Latvia, Jamaica, South Africa, Brunei Darussalam, Honduras.
