(1) Thermal Wrap Heat Jacket: Pre-installed on motor (top port on Thermal Wrap is plugged and not used for Softub applications). Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Horse Power: 1 Service Factor 1.0 (1.5hp SPL).
(1) Thermal Wrap Heat Jacket: Pre-installed on motor (top port on Thermal Wrap is plugged and not used for Softub applications). Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. 1 HP, 230 Volts, 50HZ, Single Speed with Pre-Installed “Thermal Wrap” Heater Jacket.
Softub Hot Tub Pump Replacement. Typically used in “European” markets. 1 HP, 230 Volts, 50HZ, Single Speed with Pre-Installed “Thermal Wrap” Heater Jacket. Motor & Pump with Pre-installed Thermal Wrap. Motor: Manufacture : US Motors (AGH10FL1) Horse Power: 1 Service Factor 1.0 (Often labeled 1.5hp SPL) Volts: 220-240 Amps: 6.0/6.3 RPM: 2850/3450 Frame: 48Y – Thru Bolt W/Base. Pump: (pre-installed on motor) Mfg: Balboa/Vico. 1 HP (1.5HP SPL) 1 1/2 Center Suction x Center Discharge – pump threads fit your existing pump disconnects/split unions. 1 Thermal Wrap Heat Jacket: Pre-installed on motor. (top port on Thermal Wrap is plugged and not used for Softub applications). 32″ 3/8″ ID Tubing (for making tubing connections between the 2 ports on Thermal Wrap to your existing coil/hose ports in your plumbing). More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap. Collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths. Captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). Note: If the pump/connections pictured above do not exactly match the pump have? Give me a call to discuss your application, we either have the pump you need or have other available options that will work for your application. Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including. Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. Even if you have an electric heater on your spa, the Thermal Wrap System will compliment your electric heater by capturing the waste heat. The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action.
It’s about 24 in length. Thank you for reviewing this item!
Softub Hot Tub Pump Replacement – Typically used in European market. 1 HP, 230 Volts, Single Speed with Pre-Installed “Thermal Wrap” Heater Jacket. Motor & Pump with Pre-installed Thermal Wrap. Motor: Manufacture : US Motors (AGH10FL1) Horse Power: 1 Service Factor 1.0 (Often labeled 1.5hp SPL) Volts: 220-240 Amps: 6.0/6.3 RPM: 2850/3450 Frame: 48Y – Thru Bolt W/Base. Pump: (pre-installed on motor) Mfg: Balboa – Front Discharge. 1 HP (1.5HP SPL) Bottom Suction X Front Discharge. 1 Thermal Wrap Heat Jacket: Pre-installed on motor. (top port on Thermal Wrap is plugged and not used for Softub applications). 32″ 3/8″ ID Tubing (for making tubing connections between the 2 ports on Thermal Wrap to your existing coil/hose ports in your plumbing). More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap. Collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths. Captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). Note: If the pump/connections pictured above do not exactly match the pump have? Give me a call to discuss your application, we either have the pump you need or have other available options that will work for your application. Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including. Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. Even if you have an electric heater on your spa, the Thermal Wrap System will compliment your electric heater by capturing the waste heat. The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. The item “Softub Pump 1HP 230V 6.0 Amps, 1 Speed with Thermal Wrap (replaces coil wrap)” is in sale since Tuesday, July 30, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped worldwide.
Spa Hot Tub Pump 1HP Full Rated (1.5HP SPL) – 2″ with Pre-Installed “Thermal Wrap Heater Jacket. For spas and hot tubs requiring 1 speed motors. Fits – Most application with 2 Union Connections Motor Description: Mfg: Century HP: 1 (1.5hp SPL) RPM: 3450 Single Speed 115 Volts 13.6 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL15SDCS2/2 5190-250 1 HP. 2″ Center Suction x Side Discharge (measuring 3-1/16″ across threads). Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet/Ultima Spa Pump With Thermal Wrap (Heat Transfer/Recycling System) For information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including: Quantum, Dreammaker, FreeFlo, PDC spas, SoftTub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. Feel free to contact me with any question you may have. The item “Hot Tub Pump 1hp Full Rated. Ultima, Ultra Jet 2 with Thermal Wrap Heat Jacket” is in sale since Sunday, March 16, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Softub Hot Tub Pump Replacement – Typically used in European markets. 1 HP, 230 Volts, 50HZ, Single Speed with Pre-Installed “Thermal Wrap” Heater Jacket. Motor & Pump with Pre-installed Thermal Wrap. Motor: Manufacture : US Motors (AGH10FL1) Horse Power: 1 Service Factor 1.0 (Often labeled 1.5hp SPL) Volts: 220-240 Amps: 6.0/6.3 RPM: 2850/3450 Frame: 48Y – Thru Bolt W/Base. Pump: (pre-installed on motor) Mfg: Aqua-Flo P/N. 1 HP (1.5HP SPL) 1 1/2 Center Suction x Center Discharge – pump threads fit your existing pump disconnects/split unions. 1 Thermal Wrap Heat Jacket: Pre-installed on motor. (top port on Thermal Wrap is plugged and not used for Softub applications). 32″ 3/8″ ID Tubing (for making tubing connections between the 2 ports on Thermal Wrap to your existing coil/hose ports in your plumbing). More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap. Collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths. Captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). Note: If the pump/connections pictured above do not exactly match the pump have? Give me a call to discuss your application, we either have the pump you need or have other available options that will work for your application. Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including. Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. Even if you have an electric heater on your spa, the Thermal Wrap System will compliment your electric heater by capturing the waste heat. The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. The item “Softub Pump 1HP 230 Volts, 6.0 Amps, 1 Speed withThermal Wrap replaces coil wrap” is in sale since Tuesday, July 30, 2019. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped worldwide.
Qty – 2 Pack OEM Sundance® Factory Replacement Pillow. Part # 6472-962, Old part # 6455-465 / 6455-472. This pillow is for 850/880 Series Sundance Spas® from years 2001 – 2009. Includes Pillow and Insert. Pillow is attached to spa with 2 plastic screws. Pillow fits following models with select years: Cameo, Optima, Maxxus, Metro, Marin. Pillow screws are not included. The item “Qty-2 pack, Sundance Spa OEM Wrap Around Pillow with Insert” is in sale since Monday, May 21, 2018. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “spapartsandmore” and is located in Ventura, California. This item can be shipped to United States.
Spa Hot Tub Pump 1HP with Pre-Installed “Thermal Wrap” Heater Jacket. For spas and hot tubs requiring 1 speed motors Motor Description: Motor Description: Mfg: Century HP: 1 RPM: 3450 Single Speed 115 Volts 11.8 – 12 amps HZ: 60 Frame: 56Z (48Y) Thermally Protected Pump Description: Mfg: Vico/Balboa P/N. PKUL10SDCS, 788379783402 1HP 1 1/2 Center Suction x Side Discharge. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet/Ultima Spa Pump With Thermal Wrap (Heat Transfer/Recycling System) For information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including: Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. More about the Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. The item “Hot Tub Pump 1hp Ultra Jet 1.5 with Thermal Wrap Heat Jacket BN25″ is in sale since Sunday, August 21, 2016. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
Spa Hot Tub Pump 1.5HP (Full Rated) 2″ with Pre-Installed “Thermal Wrap Heater Jacket. Dual Voltage: 115/230 volts. For spas and hot tubs requiring 1 speed motors with 2 Center Suction/Side Discharge. Note: Typically this pump and motor is used on hot tubs requiring a 230 volt motor even though it’s dual voltage. For hot tubs requiring a 115 volt motor rated at 1.5HP, we recommend our single voltage motor. Motor Description: Mfg: Century HP: 1.5 – Service factor 1.0 (2hp SPL) RPM: 3450 Single Speed 115/230 Volts – dual voltage Amps: 16.5/8.3 HZ: 60 Frame: 56Z (48Y) Thermally Protected. Pump Description: Mfg: Vico/Balboa P/N. 1215123 (Identical to PKUL15SDCS2/2, 5190-250). 1.5 HP (2HP SPL) 2″ Center Suction x Side Discharge (1.5″ Connections available) 48 Frame. Great Value – Direct From The Manufacture of the patented Thermal Wrap – Heat Recycling System. Ultra Jet Spa Pump With Thermal Wrap (Heat Transfer/Recycling System). For more information on the “Thermal Wrap” Heat Jacket. It’s like free heat! Can be used and retrofitted to work with most spas requiring 1.5 hp single speed, 3450 rpm, 115/230 volts pump motor. Note: Before ordering this “FULL RATED” 1.5 hp – as a replacement pump – make sure that your existing pump is not an “Uprated” pump. Sometimes manufactures call their pump a 1.5 HP when it’s really 1 hp. They call this an Uprated or SPL Pump. The motor amperage determines the true horse power. A 1 hp pump will be rated at approximately 11-14 amps. A 1.5 hp pump will be rated approximately 15 – 16 amps. Also note: you may think you have or need a pump for 2″ plumbing, when you actually need 1 1/2″. The pump connections measure larger than the actual pipe size used. The threaded connection on a 1 1/2″ pump measure 2 3/8″ – the threaded connections on a 2″ pump measure 3″. Unless otherwise specified, you will receive 2 pump connections with this listing. More about the – Thermal Wrap – Heat Transfer System. Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water – were it belongs! This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat “energy” produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature. The system allows the motor to run cooler; increasing the motors longevity and efficiency. There are no moving parts and nothing to wear out. Made in the USA! Patented design, over 1,000,000 in use. Special thermal conductive inner heat transfer liner. Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pump motors. Maintenance free – no moving parts to wear out. Helps keep motor cooler – increases motor longevity and efficiency. Cost less than electric heaters. No additional electrical circuits required for installation. Manufactured of non-conductive materials. Self draining design (required for whirlpool bath application). The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action. Note: Thermal Wrap color may vary. Illustration showing water flow is of a 1.5″ pump – not 2″ per list listing. The item “Hot Tub Pump 1.5hp (Full Rated) Ultra Jet 2 with Thermal Wrap Jacket Heater” is in sale since Wednesday, March 05, 2014. This item is in the category “Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Spas & Hot Tubs”. The seller is “jkc0853″ and is located in Houston, Texas. This item can be shipped to United States, Canada.
